Filter
Top Products
09:35
13-10
02/15
AM MSG
04-12
02:45
13-10
02/05
03
PM
CALL #
MSG
00-16 -5
Celestia 400
page 1
USER GUIDE
Display
see below
Microphone
ANSWER ON light
This also flashes when
the unit is ringing for an
incoming call
Model 3401
CALLER ID buttons*
skip to the next record
go back to the previous
record
clear records
call back the number
displayed
SET button
— enter or leave
Settings mode
MEMO/<</– button
— record a memo
— rewind during
message playback
— decrease value in
Settings mode
OGM/>>/+ button
— record an outgoing message
— fast-forward during message
playback
— increase value in Settings mode
DELETE/ANSWER ON button
— switch the answering
machine on and off
— delete recorded messages
— leave Settings mode without
changing settings
PLAY/PAUSE/STOP button
— start, pause and stop
message playback
— in Settings mode, move
from one setting to the next
SPEAKERPHONE button
— press while the unit is recording
an incoming message, to stop
recording and speak to the caller
The display
This appears when you press the
SPEAKERPHONE button to listen
and/or speak to a caller; or when you
call back a number from the Caller ID
memory
The bell appears when the unit is
ringing for an incoming call (even if
the ringer is turned off)
This shows the loudspeaker volume currently set
After the Celestia 400 has been connected to the
line for 16 seconds, the call duration is shown here
When you call back a number from Caller ID
memory, the record number is shown here
While the Celestia 400
is idle, the display
shows information as
in this example:
Other information and
symbols that appear
on the display include:
The time and date — 9.35 am
on 13 October
There are 2 new caller ID records
and 12 records altogether
There are 4 new incoming messages
or memos and 15 messages/memos
altogether
* Please note that, to use these features, you need to
subscribe to the BT Caller ID option, or the equivalent
option from your service provider.
The and buttons can also be used to adjust
the speaker and ringer volumes (see page 7)
page 8
If you need help, call the Binatone Help Line
9.00 am to 5.00 pm, Monday to Friday
020 8344 8870
The Celestia 400 must be serviced by trained
engineers. NEVER attempt any repairs or
adjustments yourself — you could make the
problem worse and invalidate the Guarantee.
Always make sure your Celestia 400 is fully
plugged into the telephone line socket and the
mains power socket.
Check that the ringer volume is not set to .
Check that the total REN value of all
equipment connected to your telephone line is
no more than 4. Disconnect one or more
telephones and see whether that helps.
Disconnect all other instruments connected to
the same line as the Celestia 400 and see
whether you can make a call.
Disconnect the Celestia 400 from the
telephone line and plug a telephone into the
socket. Try making a call. If this works, the line
is OK.
If you are using a two-way socket adapter,
remove it and plug a telephone directly into
the socket. If the call now works, the adapter
may be faulty.
If you think the fault may be on the exchange
line, contact the service provider (the BT
engineers on 151, or your cable company).
If the phone does not ring …
If you cannot dial out …
-0
If you still cannot identify the cause of the
problem, contact the Binatone Help Line.
Troubleshooting
Turning the ringer on and off
SETTINGS
Technical details
Temperature range Operating 0ºC to 40ºC
Storage -20ºC to 60ºC
Approvals CTR 21
Input 230 V AC, 50Hz, AC9 V, 200 mA
Mains adapter part number XX002104D
The AC port (connected to the mains power supply) is a
SELV port with respect to EN41003
Default settings
Time and date 12:00 am on 01-01
Max. incoming message length 3 minutes
Security code 123
Ring count 2
If the unit is disconnected from the telephone line, all
settings will be returned to these defaults.
Binatone Telecom plc operates a policy of continuous product
improvement, and so reserves the right to make changes to the
product and functions without notice.
By default, the ringer is on.
1
2
3
Press
Press
Press
the PLAY/PAUSE/STOP button twice
or to switch the ringer on or off
Press to save the new setting and leave Settings mode
OR press to leave Settings mode without saving any changes
OR press PLAY/PAUSE/STOP to go back to setting the time and date
The Celestia says: ‘Ring on’ or ‘Ring off’.
4
memo