Filter
Top Products
Thank you for purchasing this SUPER DIRECTIONAL MICROPHONE. To get maximum benefit from its use, it is suggested that
you read this instructions carefully. After reading, please keep this instructions for future reference.
MV-P618
SUPER DIRECTIONAL MICROPHONE
Instructions
INSTALLATION
(An example of mounting on the GY-DV300 by using KA-A33)
1.
Loosen the mounting screws on the microphone holder
and install the microphone holder on the mount base.
2.
Turn the knob on the microphone holder counterclock-
wise to open the microphone holder.
3.
Mount the microphone on the microphone holder.
4.
Turn the knob on the microphone holder clockwise to
clamp the microphone.
5.
Attach the microphone cable to the cable clamp on the
microphone holder and connect the cable to the MIC 1 or
2 input connector.
COMPATIBLE UNITS
MV-P618 : JVC camera equipped with an XLR 3-pin connector supplying 48 V (phantom)
PRECAUTIONS
• MV-P618 is a SUPER DIRECTIONAL MICROPHONE exclusively for JVC color video cameras.
• Do not drop or hit the microphone. A strong shock may degrade the characteristics of microphone.
• Do not disassemble the microphone. The original performance may not be obtained.
• Be careful not to use or leave long time the microphone in a hot or humid place, such as, direct sunlight, near a heater, closed
automobile in summer.
Ⅵ Notes for operation
• MV-P618 is a high-sensitivity microphone designed to give optimum performance. This is designed to give best performance at
a certain distance from the source. Do not locate your microphone too close to the source. Otherwise the tone balance is
disordered due to the proximity effect.
• A loud sound near the microphone may cause to distort the sound signal due to the built-in mic amp of the camera. In addition,
the sound level may fluctuate due to AGC of VCR. (Adjust the volume control of the camera to avoid sound signal distortion.)
• When this unit is used on the GY-DV300, it may pick up the operating noise of the camera.
To reduce this noise, set the menu item of the GY-DV300 WIND CUT in the SYSTEM [1/2] to ON.
In this case, however, note that low frequencies may not be picked up properly.
• While recording, always monitor the sound level with headphone etc.
• Do not wet the microphone. (Especially when using in rainy conditions.)
Attachment
base
Screw
hole
Microphone
holder
1.
2.
Knob
Attachment
screw
Cable
clump
MIC1
MIC2
4.
3.
5.
This instruction book is made from 100% recycled paper.
This unit can be installed on the camera using the optional
KA-A33 microphone holder.
MICROPHONE CHARACTERISTICS
SPECIFICATIONS
Reception : Second-order pressure gradient
super-directional
Type : Back-electret condenser type
Sensitivity :
–62 dB (0 dB = 1 V/0.1Pa, at 1 kHz, 0°)
Frequency response : 200 Hz to 10,000 Hz
Output impedance :50ע20 Ω
Max. input SPL : 115 dB SPL or more
(1 kHz, 1% distortion, microphone itself)
S/N ratio : More than 42 dB
Connector : 3-pin XLR (male)
Power supply voltage : 48 V (Phantom)
Current consumption : 2.6 mA
Ambient temperature : –5°C to 45°C
Dimensions : Microphone
160 mm(L) x 21 mm(Dia.) (With windscreen)
Mass : 85g (With windscreen)
Accessory : Windscreen
• Design and specification subject to change without notice.
-40
-50
Frequency (Hz)
Response
-60
-70
-80
-90
50 100 200 500 1K 2K 5K 10K 20K
(dB)
Standard Directional Characteristics Standard Frequency Response
0°
180°
270°
90°
-10dB
-20dB
0dB
© 2002 VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
LWT0056-001B
VICTOR COMPANY OF JAPAN, LIMITED
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.
R
R
R