Filter
Top Products
103
4a. Select ChannelPair ............................. [1 2…5 6]
Press the “1 2”–“5 6” button for the channels that
you wish to pair. When pairing is “On,” the heart
icon will be displayed.
4b. Select Function....................[Eq, Send, Aux, Pan]
Select the functions that will be paired for the chan-
nels selected by “Select ChannelPair.”
For the functions “EQ”–”Pan” that you wish to pair,
press the button to enable pairing (the button will
be highlighted). The settings will be applied when
you press the “OK” button.
When pairing is on, the pairing function will
always apply to the fader and track status.
P2 Ch7–12: Select the inputs for
mixer channels 7–12
Here you can select the inputs for mixer channels 7–12.
Refer to “P1 Ch1–6: Select the inputs for mixer channels
1–6.”
P3 InEq1–4: EQ settings for inputs
1–4
Here you can apply EQ (equalizer) to the analog inputs
from the [INPUT 1/GUITAR IN]–[INPUT 4] jacks.
Make these settings when you wish to directly record
the sound that is adjusted by the EQ.
The EQ has three bands. High EQ and low EQ are
shelving type, and the mid EQ is a peaking type with
adjustable cutoff frequency.
This EQ cannot be used on the digital input (S/P
DIF IN) or on the rhythm.
1. InputLevelMeter .......................................................
(1, 2, 3, 4/CLP, –6, –12, –18, –40dB)
This shows the level of each analog input.
The horizontal axis indicates the channel, and the
vertical axis indicates the level.
Inputs that are not selected in “Ch1…6” ([INPUT]
P1-1) will not be displayed.
2. InputHigh ..................[(Fc=10kHz)–15.0…+15.0(dB)]
Set the input high EQ gain. This adjusts the high-
frequency range.
You can cut/boost over a range of –15.0 – +15.0 dB
at a 10 kHz cutoff frequency.
3. InMidFc .....................................[100Hz…20.0k(Hz)]
Set the cutoff frequency for the input mid EQ.
This can be adjusted over the range of 100 Hz–20.0
kHz.
4. InputMid.................................... [–15.0…+15.0(dB)]
Set the input mid EQ gain.
This adjusts the mid-frequency range.
You can cut/boost over a range of –15.0 – +15.0 dB
at the cutoff frequency specified by “InMidFc.”
5. InputLow ...................[(Fc=100Hz)–15.0…+15.0(dB)]
Set the input low EQ gain.
This adjusts the low-frequency range.
You can cut/boost over a range of –15.0 – +15.0 dB
at a 100 Hz cutoff frequency.
6. Pair........................................................................
Enable pairing for adjacent mixer channels. (→p.102
“Pair”)
P4 Tuner: Tuner
You can use the built-in tuner to tune an instrument
connected to the [INPUT 1/GUITAR IN] jack or input
from the built-in mic. You can also measure the pitch of
a track.
This page cannot be selected during recording or
playback. Nor is recording possible.
To allow tuning to be performed accurately, the
effects will be turned off while this page is dis-
played.
1. CENT Scale ............................................ (–50…+50)
The “▼” symbol in the center will change to “▼”
when the tuning is correct. The amount of pitch
deviation is shown in units of cents (100 cents = 1
semitone, and 1200 cents = 1 octave)
2. NoteDisplay................................................... (C…B)
This shows the name of the note that is closest to the
input sound.
It is not possible to detect the pitch if two or more
notes are played simultaneously.
3. Calib ....................................... [435…440…445Hz]
Specify the frequency that will be the basis for tun-
ing. Normally you will set this to “440.”
4. SelectSource ....................... [Input1, Track No1…12]
Input1: Select this when you wish to tune an exter-
nal device such as a guitar, or when using the built-
in mic to tune.
Track No “1…12”: Select the track whose pitch you
wish to measure. Move to the time location that you
wish to measure, then specify the track in this page,
and play back to measure the pitch of the specified
track.
1
324
5
6
3
1
4
2
Refer
e
INPUT