Filter
Top Products
Refer
e
RECORDTRACKSONGSTOREMARKSCENELOOPUNDOSCRUBENTERINPUTEQINS EFFSOLOMETERPANFADERTRANSPORT STATUS MAST EFF TEMPOIN/LOC1TRIGGER AT PUNCH COUNTERSYSTEM
75
R
e
f
erence
Counter: Counter display
The counter located in the upper right of each page
shows the current location of the recorder.
1. Select TimeDisp Type................................................
This switches the counter display. When you press
the “ ” button at the left of the counter, the “Select
TimeDisp Type” dialog box will appear. Select the
desired type of display, and press the “OK” button.
___.__.___ (MBT): The current location will be
shown in measures from the beginning of the song.
From the left, the numbers indicate the Measure,
Beat, and Tick (1/96 beat).
___:__.___ (MSM): The current location will be
shown as an absolute time from the beginning of
the song.
From the left, the numbers are Minutes: Seconds.
Milliseconds (1/1000 second).
__:__.__F (MSF): The current location will be dis-
played as the absolute time and the number of
frames from the beginning of the song. You will
normally select this display type if you are using
MTC synchronization.
From the left, the numbers are Minutes: Seconds.
Frames (1/30 second).
___.__Free (Free Time): The remaining time avail-
able for recording on the currently selected drive
will be shown.
From the left, the numbers are Minutes . Seconds.
To change the current time of the counter, move the
cursor to the counter value, and use the [VALUE]
dial to change the value. (→p.35)
P1 Control: Foot switch/control
change device (pedal/MIDI)
settings
1. Pol(FootSwPolarity) .........................................[– , +]
This sets the polarity of the foot switch.
Connect a foot switch (such as the separately sold
PS-1 option) to the front panel [FOOT SWITCH]
jack, and set this parameter so that the polarity indi-
cator “ ” is lit when you press the foot switch.
2. Func(FootSwFunction)..............................................
[PunchIn–Out, Play/Stop, Mark]
Select the function that the foot switch will control.
PunchIn–Out: The foot switch will start/stop man-
ual punch recording. Use the [TRACK STATUS]
keys to set the desired track to REC, begin playback,
and press the foot switch at the location where you
wish to begin recording. Press the foot switch again
to stop recording. (→p.28)
Play/Stop: The foot switch will start/stop playback.
Press the foot switch to start playback, and press it
again to stop playback.
Mark: The foot switch will register a mark.
When you press the foot switch, a mark will be reg-
istered at that time location.
While this page is displayed, the foot switch will be
used only to verify the polarity, and the specified
function will be disabled.
Also during tap recording, the function you select
here will be ignored, and the foot switch will auto-
matically function as a tap marker. (→p.63)
3. Device(CtrlChgDevice)..............................................
[Pedal, A.Touch, PitchBend, Velocity, NoteNum,
CC#000…119]
Select the external device that will control the inter-
nal effects of the D12. The effect selected by “Ass
”
(P1-4) can be controlled in realtime.
Pedal: An expression pedal can be used to control
the effect. Connect an expression pedal (separately
sold option: XVP-10, EXP-2 etc.) to the [EXPRES-
SION PEDAL] jack, and operate the pedal to control
the effect.
A.Touch, PitchBend, Velocity, NoteNum: MIDI
aftertouch, pitch bend, velocity, or note number
data can be used to control the effect.
1. COUNTER
1
MBT
MSF
MSM
FreeTime
2. SYSTEM
3
2
1
4