Filter
Top Products
100
68: MM14: Exciter – Limiter
[Excit2, Limitr]
69: MM15: Exciter – Cho/Flng
[Excit2, ChFl1]
70: MM16: Exciter – Phaser
[Excit2, Phaser]
71: MM17: Exciter – Mt.Delay
[Excit2, Mt.Dly]
72: MM18: Limiter – P4EQ
[Limitr, P4EQ]
73: MM19: Limiter – Cho/Flng
[Limitr, ChFl2]
74: MM20: Limiter – Phaser
[Limitr, Phaser]
75: MM21: Limiter – Mt.Delay
[Limitr, Mt.Dly]
76: MM22: OD/HiG – Cho/Flng
[OD/HiG, ChFl1]
77: MM23: OD/HiG – Phaser
[OD/HiG, Phaser]
78: MM24: OD/HiG – Mt.Delay
[OD/HiG, Mt.Dly]
79: MM25: OD/HiG – AmpSim
[OD/HiG, AmpSim]
80: MM26: Wah – AmpSim
[Wah, AmpSim]
81: MM27: Decimator – AmpSim
[Decima, AmpSim]
82: MM28: Decimator – Comp
[Decima, Comp1]
83: MM29: Cho/Flng – Mt.Delay
[ChFl2, Mt.Dly]
84: MM30: Phaser – Cho/Flng
[Phaser, ChFl2]
85: MM31: AmpSim – Tremolo
[AmpSim, Treml]
86: MM32: Reverb – Gate
[Reverb, Gate]
87: MM33: MicSim - Limiter
[MicSim, Limitr]
Effects within multi-effect programs
MM1–MM33, and their parameters
Here are explanations of the parameters of each effect in the
multi-effect chains listed above.
P4EQ (Parametric 4band EQ)
Excit1 (Exciter1)
Excit2 (Exciter2)
This adds Pre LEQ and Pre HEQ to Exciter 1.
Wah (Wah/Auto Wah)
:Mode
Select “Pedal” if you wish to use an expression pedal to control the
wah.
Comp1 (Compressor1)
Comp2 (Compressor2)
This effect adds Pre LEQ and Pre HEQ to Comp1.
Trim (Trim).........................................0...100 Sets the parametric EQ input level
Fc1 (Band1 Cutoff [Hz]).............20...1.0kHz Sets the center frequency of Band 1
Q1 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 1
G1 (Gain [dB]).......................... –18...+18dB Sets the gain of Band 1
Fc2 (Band2 Cutoff [Hz]).............50...5.0kHz Sets the center frequency of Band 2
Q2 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 2
G2 (Gain [dB]).......................... –18...+18dB Sets the gain of Band 2
Fc3 (Band3 Cutoff [Hz]).........300...10.0kHz Sets the center frequency of Band 3
Q3 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 3
G3 (Gain [dB]).......................... –18...+18dB Sets the gain of Band 3
Fc4 (Band4 Cutoff [Hz]).........500...20.0kHz Sets the center frequency of Band 4
Q4 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 4
Gain4 (Gain [dB])..................... –18...+18dB Sets the gain of Band 4
Blend (Exciter Blend)................–100...+100 Sets the intensity (depth) of the Exciter
effect
Empha (Emphatic Point)...................0...140 Sets the frequency range to be empha-
sized
Blend (Exciter Blend)................–100...+100 Sets the intensity (depth) of the Exciter
effect
Empha (Emphatic Point)...................0...140 Sets the frequency range to be empha-
sized
Trim (EQ Trim)...................................0...100 Sets the EQ input level
LEQG (Pre LEQ Gain [dB])...... –15...+15dB Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB]) ....–15...+15dB Sets the gain of High EQ
FcBtm (Frequency Bottom)...............0...100 Sets the lower limit of the wah center
frequency
FcTop (Frequency Top).....................0...100 Sets the upper limit of the wah center
frequency
*Mode (Sweep Mode).........Auto, Pedal, LFO Selects the control from auto-wah,
modulation source, and LFO
*Speed (LFO Frequency [Hz]).0.02...20.0Hz Sets the LFO speed
Reso (Resonance)............................0...100 Sets the resonance amount
LPF (LPF)........................................ Off, On Switches the wah low pass filter on and
off
Sense (Sensitivity)............................1...100 Sets the sensitivity
Attack (Attack)...................................1...100 Sets the attack level
Level (Output Level)..........................0...100 Sets the output level of the compressor
Sense (Sensitivity)............................1...100 Sets the sensitivity
Attack (Attack)...................................1...100 Sets the attack level
Level (Output Level)..........................0...100 Sets the output level of the compressor