Filter
Top Products
Reference
COUNTERSYSTEMRECORDTRACKSONGSTOREMARKSCENELOOPUNDOSCRUBENTERINPUTEQINS EFFSOLOMETERPANFADERTRANSPORT STATUS MAST EFF
TEMPOIN/LOC1
TRIGGER AT PUNCH
45
Reference
Counter: Counter display
The counter located in the upper right of each page
shows the current location of the recorder.
Use the following procedure to switch the counter dis-
play.
1 Press the “ ” button at the left of the counter to
access the “Select Time Disp Type” dialog box.
2 Select the desired type of location display, and press
the “OK” button.
___.__.___ (MBT): The current location will be shown
in measures from the beginning of the song.
From the left, the numbers indicate the Measure, Beat,
and Tick (1/96 beat).
___:__.___ (MSM): The current location will be shown
as an absolute time from the beginning of the song.
From the left, the numbers are Minutes : Seconds. Milli-
seconds (1/1000 second).
___:__.__F (MSF): The current location will be shown
as an absolute time from the beginning of the song.
This is normally used when synchronizing with MTC.
From the left, the numbers are Minutes : Seconds.
Frames (1/30 second).
___.__Free (Free Time): The remaining time available
for recording on the currently selected drive will be
shown.
From the left, the numbers are Minutes . Seconds.
To change the current time location at the cursor,
either press the counter value or use [CURSOR] to
move to the value, and use the [VALUE] dial to
change the value.
P1 Control: Foot switch/control
change device (pedal/MIDI)
settings
1. Pol(FootSwPolarity) ................................ [– , +]
This sets the polarity of the foot switch.
Connect a foot switch (such as the separately sold
PS-1 option) to the front panel [FOOT SWITCH]
jack, and set this parameter so that the polarity indi-
cator “*” is lit when you press the foot switch.
2. Func(FootSwFunction) ......................................
[PunchIn–Out, Play/Stop, Mark]
Select the function that the foot switch will control.
PunchIn–Out: The foot switch will start/stop man-
ual punch recording. Use the [TRACK STATUS]
keys to set the desired track to REC, begin play-
back, and press the foot switch at the location
where you wish to begin recording. Press the foot
switch again to stop recording. (→p.20)
Play/Stop: The foot switch will start/stop playback.
Press the foot switch to start playback, and press it
again to stop playback.
Mark: The foot switch will register a mark. When
you press the foot switch, a mark will be registered
at that time location.
While this page is displayed, the foot switch will be
used only to verify the polarity, and the specified
function will be disabled.
Also during tap recording, the function you select
here will be ignored, and the foot switch will auto-
matically function as a tap marker. (→p.42)
3. Device(CtrlChgDevice).............. [Pedal, A.Touch,
PitchBend, Velocity, NoteNum, CC#000…119]
Select the external device that will control the inter-
nal effects of the D16. The effect selected by “Ass
”
(P1-4) can be controlled in realtime.
Pedal: An expression pedal can be used to control
the effect. Connect an expression pedal (separately
sold option: XVP-10, EXP-2 etc.) to the [EXPRES-
SION PEDAL] jack, and operate the pedal to con-
trol the effect.
A.Touch, PitchBend, Velocity, NoteNum: MIDI
aftertouch, pitch bend, velocity, or note number
data can be used to control the effect. Connect the
1. COUNTER
MBT MSM
MSF FreeTime
2. SYSTEM
3
2
1
4