Filter
Top Products
79
The insert effects can be applied to the analog inputs
during recording, or to track playback.
The D16 lets you use up to eight different insert effects
simultaneously.
Insert effects cannot be used if “DigiIn” is turned
“On” in the [INPUT] “Ch1–8” or “Ch9–16” tab
pages.
Be aware that the location at which insert effects are
inserted has a pre-specified priority beginning with
the lower-numbered effects.
P1 InsAss: Insert effect insertion
location/type
1. Assign ........................[In(Input), Trk(PlayTrack)]
Select whether the insert effect will be applied to an
analog input or to a playback track.
In (Input): Use these settings to apply an effect to
analog inputs from the [INPUT 1/GUITAR IN]–
[INPUT 8] jacks while recording.
Trk (PlayTrack): Use these settings to apply an
effect to a playback track. Effects can also be used
during mixdown.
2. SelectEffType................ [1in2outx2, 2in2outx2,
1in1outx4, 1in1outx8]
Select the configuration of insert effects.
The effects that can be selected will depend on this
setting. For the effects that are available for each
configuration, refer to “Effect Program List”
(→p.112).
1in2outx2: Select this when you wish to use two
mono-in/stereo-out effects.
This is ideal when you wish to add more spacious-
ness to a lead guitar or vocal.
This can be selected only if “Assign” is “In.”
2in2outx2: Select this when you wish to use two ste-
reo-in/stereo-out effects.
This is ideal for stereo input sources such as key-
board.
1in1outx4: Select this when you wish to use four
mono-in/mono-out effects.
This is ideal for sources for which the panning is
fixed, such as rhythm guitar.
1in1outx8: Select this when you wish to use eight
mono-in/mono-out effects.
This is ideal for sources for which the panning is
fixed, such as drums.
3. InsertTo...........................................................
Select the location at which the insert effect will be
inserted.
Press the “ ” button to access the dialog box and
make settings. Press the “OK” button to execute
your settings, or press the “Cancel” button to cancel
them.
Be aware that these settings will be reflected by the
mixer channel input settings (→p.75 [INPUT]
“Ch1”–“Ch16”).
■ When “Assign” is “In”
The signal flow will be: input select → (effect) →
return channel.
3a. SelectInput .................... [In 1…8, DrL, DrR]
In 1…8: Select an analog input [INPUT 1/GUITAR
IN]–[INPUT 8] jacks).
DrL, DrR: Select rhythm L or R.
When “SelectEffType” is 2in2outx2,” the avail-
able choices for “SelectInput” will be odd-num-
bered “In1”–”In8,” and “DrL.”
3b. Effect ...............................................(1…8)
This shows the effect number.
3c. SelectCh ..................................[1…16, Off]
Specify the return channel for the effect output.
■ When “Assign” is “Trk”
The signal flow will be: input channel select →
(effect) → (return = insert channel).
3a. SelectCh..................................[1…16, Off]
Select the insert destination mixer channel.
When “SelectEffType” is “2in2outx2,” only
odd-numbered channels can be selected for
“SelectCh.”
3b. Effect ...............................................(1…8)
This shows the insert effect number.
3c. SelectCh ..................................(1…16, Off)
This shows the return channel of the effect output.
The same channel as “3a. SelectCh” will be selected.
4. Pair
You can specify that adjacent mixer channels be
paired. (→p.76 ”Pair”).
19. INSERT EFFECT
1
23
4
3a
3c3b
Reference
EQINS EFF