Filter
Top Products
0001
0001
INSTR,INST,AE1 MECH/ELEC
Linear P/N: 213071 B
Material: 20 Lb. Mead Bond
Size: 8.500 x 11.000"
Ink: Black
Scale: 1-1
Front Side 1 of 2
AE-1
Telephone Entry Control Console
Mechanical & Electrical
Installation Instructions
(760) 438-7000 • FAX (760) 438-7043
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
INTRODUCTION
The Model AE-1 Telephone Entry Control Console is designed for use as a primary
access control device for gated communities, parking garages, office buildings,
apartments, dormitories, hotels/motels, commercial buildings and recreational facilities.
This unit is a fusion of Linear’s full-featured Model AM/II Access Control System and
the Model AE-1 Telephone Entry Module. Housed in a locked, rugged stainless steel
enclosure, the AE-1 features a 12-key telephone style keypad, a backlit two-line
directory display, and a built-in microphone and speaker.
All of the outstanding AM/II access control system functions are available with the AE-1 in
addition to hands-free, full duplex telephone communications with tenants or authorized
personnel for granting access. Entry codes can also be typed directly on the keypad.
In a typical installation, the unit’s memory would be programmed with each tenant’s
name and directory code number. A visitor would use the
*
or # key on the AE-1 to view
the directory names and code number for the desired party. Upon entering the directory
number, the AE-1 will automatically dial the tenant’s telephone number and establish
two-way voice communication between the visitor and the tenant. The tenant will then
have the option to grant access to the guest by pressing a digit on their telephone.
In addition to the telephone entry, the AE-1 can grant access using various remote
devices that are commonly used with the AM/II. These devices include wireless
transmitters, proximity receivers, swipe card readers and remote keypads.
The output relays can be programmed to control electric door strikes, door & gate
operators, barrier gates. CCTV cameras can also be triggered by the output relays to
monitor the entry areas.
All of the programming functions of the AE-1 can be performed directly through the
unit’s keypad. An optional telephone modem can be installed for easy remote
programming with a personal computer.
The AE-1 cabinet has provisions for installing a postal lock for keyed mail carrier access.
The postal lock can be programmed to activate any of the four output relays.
1. SYSTEM COMPONENT LOCATIONS
2. AE-1 COMPONENT LOCATIONS 3. DETERMINE MOUNTING LOCATION 4. MOUNT CABINET
AM/II ACCESS
CONTROL SYSTEM
MODEM
(OPTIONAL)
SPEAKER
POSTAL LOCK
LOCATION
(LOCK OPTIONAL)
POSTAL LOCK
SWITCH
AE-1 TELEPHONE
ENTRY MODULE
MICROPHONE
(HIDDEN)
MODULAR
TELEPHONE
JACK (HIDDEN)
TELEPHONE
LINE TERMINALS
HYBRID LEVEL
ADJUSTMENT
(FACTORY SET
DO NOT ADJUST)
SPEAKER
VOLUME
ADJUSTMENT
AE-1 TO AM/II
INTERCONNECT
CABLE
ON-LINE INDICATOR
(LIGHTS WHEN PHONE
LINE IS ACTIVE)
DISPLAY
CONTRAST
ADJUSTMENT
BUSY INDICATOR
(LIGHTS WHEN AE-1 IS
COMMUNICATING OR WHEN
PHONE LINE IS DISCONNECTED)
SPEAKER
CONNECTOR
TEST JUMPER
(REMOVE TO
HEAR UNIT DIAL)
MICROPHONE
& POSTAL KEY
SWITCH TERMINALS
THE AE-1 SHOULD BE MOUNTED IN A WELL LIT LOCATION NEAR THE
CONTROLLED OPENING. WIRING ACCESS FOR POWER, TELEPHONE,
EARTH GROUND, CONTROL OUTPUT AND ANTENNA CO-AX MUST BE
AVAILABLE BEHIND THE MOUNTING LOCATION.
AE-1
TELEPHONE
ENTRY SYSTEM
CONTROLLED
ENTRY DOOR
AREA
LIGHTING
5 3/8" 5 3/8"
9 3/8"
5 3/8" 5 3/8"
MOUNT CABINET WITH
SUITABLE HARDWARE FOR
MOUNTING SURFACE.
USE TOGGLE BOLTS FOR
STUCCO WALL, WEDGE
ANCHORS OR EXPANSION
BOLTS FOR CONCRETE
WALL, LAG SCREWS FOR
WOOD WALL.
MOUNTING
LOCATION