Yamaha S30 Electronic Keyboard User Manual


 
109
Performance Mode
Point
When the Mode (see earlier) has been set to “split,”
this sets the split point. The actual note of the split
point will be assigned to the upper section.
You can also select the split point by pressing the note
while holding down the [SHIFT] key.
Settings: C-2 ~ G8
Master keyboard setting list (on split/layer)
For more information about the master keyboard mode,
refer to page 52 in Basics Section.
Common Quick Edit
You can set various parameters governing the sonic
properties of the Layer Part, The following four
screens are only available when the Layer switch (Page
117) for each Part is set to on.
QED Level (Quick Edit Level)
QED EF (Quick Edit Effect)
QED Filter (Quick Edit Filter)
QED EG (Quick Edit Envelope Generator)
Split Layer
Prameter Name
TrnsCh
TG
MIDI
Octave
Transpose
Note Limit Low
Note Limit High
Transmit Switch PB
Transmit Switch MW
Transmit Switch KnobA-C
Transmit Switch Knob1/2
Transmit Switch FC
Transmit Switch AT
Transmit Switch FS
Transmit Switch Vol
Transmit Switch Pan
Transmit Switch Bank Select
Transmit Switch Program Change
Transmit Preset Volume
Transmit Preset Pan
Transmit Preset Bank MSB
Transmit Preset Bank LSB
Transmit Preset PC
CS Control Number Assign
Zone1
ch
on
on
+0
+0
C-2
p
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone2
ch+1
on
on
+0
+0
p
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone3
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone4
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone1
ch
on
on
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone2
ch+1
on
on
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone3
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone4
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
ch: Keyboard transmit channel
p: split point
Details about each parameter are given on page 121
QED Level (Quick Edit Level)
You can set output level and pan parameters for each
Layer Part. The settings are also available in the Part
Edit screens.
Vol (Volume)
Set the output level of the Layer Part.
Settings: 0 ~ 127
Pan
Set the stereo pan position of the Layer Part.
Settings: L63 (Left) ~ C (Center) ~ R63(Right)
RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the by-passed signal) to the Reverb
effect.
Settings: 0 ~ 127
ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the by-passed signal) to the Chorus
effect.
Settings: 0 ~ 127
QED EF (Quick Edit Effect)
You can set the amount of Chorus applied to the Layer
Part, as well as Portamento settings.
Chorus
Set the Return level of the Chorus effect as an offset
value.
Settings: -64 ~ 0 ~ +63
Portamento
Switch Portamento on or off.
Settings: off, on
Time
Set the pitch transition time. Higher values mean
longer transition times.
Settings: -64 ~ 0 ~ +63
QEDíEF) Chorus Portamento-Time
Common -63 off 127
QEDíLevel) Vol Pan RevSend ChoSend
Common 127 C 63 63