Filter
Top Products
SPECIFICATIONS FOR 119L / 119LB / 119L-19
Specifications
Generating Element:
Dynamic
Polar Pattern:
Unidirectional (Cardioid)
Frequency Response:
80 Hz - 15 KHz
Output Level: @ 1000 Hz
Open Circuit Voltage:
-77 dB (0 dB=1 volt/microbar)
-60 dB (0 dB=1 mv/10 microbar)
1.4 mv/PA
Front To Back Ratio:
20 dB
Impedance:
Low, 500 ohms
Cable:
Two conductor, overall shielded permanently attached, rugged,
synthetic, jacketed cable.
119L, 119LB - 2.1m (7ft) / 119L-19 - 1.7m (5.5ft)
Dimensions:
See Drawing
Weight:
119L, 119LB - 227 grams (8oz)
119L-19 - 340 grams (12 oz.)
Housing:
Die cast Zinc
Finish:
119L - Plated satin chrome
119LB - Black
Phasing
Positive Pressure (movement of diaphragm inward)
will generate a positive voltage on the red cable lead with respect to
the black cable lead.
TWO-YEAR LIMITED WARRANTY
Omnitronics, LLC (“ASTATIC”) hereby warrants that this product will be free of defects in material and workmanship for a period of two years
from the date of purchase. In the unlikely event a defect occurs ASTATIC will, at its option, either repair or replace with a new unit of equal or
greater value. You should retain proof of purchase to validate the purchase date and return it with any warranty claim. Contact Customer Service
for a pre-approved Return Authorization Number and return warranty claims carefully packed, insured and prepaid to the Service Department
at the address listed below.
This warranty excludes exterior finish or appearance, damage from abuse, misuse of the product, use contrary to ASTATIC’s instructions or
unauthorized repair. All implied warranties or merchantability or fitness for a particular purpose are hereby disclaimed and ASTATIC hereby
disclaims liability for incidental, special or consequential damages resulting from the use or unavailability of this product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions and
limitations may not apply to you.
Note: No other warranty, written or oral is authorized by Omnitronics, LLC.
Architects' and Engineers' Specification
The microphone shall be an ASTATIC 119L, 119LB or 119L-19. The
microphone shall be a dynamic moving coil type with a diaphragm made of
polyester. The frequency response shall be 80 Hz to 15 KHz. The
microphone shall have a cardioid polar pattern.
The output level of the 119L Series (500 ohms) shall be -60 dB (0 dB = 1
mW/10 microbar); -77 dB (0 dB = 1 volt/microbar); 1.4 mV/Pa. The
microphone will feature an internal shock mounted element to reduce
gooseneck and handling noise. The microphone will be wired for balanced
line operation. The microphone will have a zinc die cast and brass housing
and be finished in satin chrome (119L), and black (119LB). The 119L-19
microphone will be fitted with a 508mm (20") chrome flexible gooseneck
and mounting flange. The 119L and 119LB shall have a permanently
attached 2.1 M (7ft) two conductor overall shielded synthetic jacketed
cable. The 119L-19 shall have a permanently attached 1.7M (5 1/2') two
conductor overall shielded synthetic jacketed cable.
The overall dimensions shall be 31.8mm (1 1/4") in diameter; 103.2mm (4
1/16") long and for the 119L-19 plus 508mm (20") for the gooseneck and
flange. The weight shall be 340 grams (12 oz.) including gooseneck for the
119L-19 and 227 grams (8 oz.) for the 119L and 119LB.
The ASTATIC Model 119L, 119LB or 119L-19 is specified.
46873-46-00 / Rev.1 / 6/10/04