Filter
Top Products
RESPONSE IN dB
+10
0
-10
-20
-30
10
50
100
500
1K
5K
10K
20K
FREQUENCY IN HERTZ
SPECIFICATIONS FOR 901R
Specifications*
Generating Element:
Electret Condenser
Polar Pattern:
Cardioid
Frequency Response:
100 Hz - 20 kHz
Sensitivity Level:
-33 dBV (22mV) @ 1Pa
Impedance:
150 ohms
Self Noise:
25dBA
Maximum SPL:
127 dB, 1% THD, 1kHz
Powering:
P12, P24 and P48, 2.4mA
Phasing
Positive pressure on diaphragm generates a positive voltage on pin
2 relative to pin 3
Finish:
901R - Durable black urethane
Dimensions:
(See drawing on other side)
Net Weight:
190 grams (6.7 oz.)
RF Immunity:
Exceeds EN55103-2, E1, E2, E3 and E4
RoHS Compliant
*In our constant efforts to maintain excellence, ASTATIC reserves the right to change these
specifications at any time and without prior notice.
Architects’ and Engineers’ Specification
The microphone shall be a ASTATIC 901R. The microphone shall be a miniature
electret boundary microphone. The frequency response will be 100 - 20kHz.
The microphone shall contain in itegral 80Hz / 12dB / oct hi-pass filter to
remove unwanted low frequency energy. The microphone shall have a cardioid
polar pattern in the horizontal plane.
The sensitivity of the 901R shall be -33 dB (22mV) @ 1 Pa. The microphone
shall have a miniature 3 pin connector and be supplied with a 30 foot cable that
has a mating connector on one end and a professional 3 pin XLR type connector
on the other end. The microphone shall operate from standard P12, P24 and P48
phantom power with a current consumption of less than 3 mA.
The dimensions of the microphone shall be 4-9/32" (109mm) long, 3" (76mm)
wide, and 25/32" (20mm) high. The weight shall be 6.7 oz. (190 grams) not
including the cable. The microphone shall have a durable urethane painted
finish. The 901R shall be black with a black cable.
The ASTATIC Model 901R is specified.
User Techniques and Applications
The 901R should be used on a large flat surface located preferably in the center
positioned with the front of the microphone facing the sound source.
The surface can be a part of the structure such as a wall or ceiling, or any flat
object such as a table with equally good results. Best results will be obtained
from larger smooth surfaces of at least 4'x4' with no obstructions. Smaller
surfaces will reduce low frequency sensitivity.
TWO-YEAR LIMITED WARRANTY
Omnitronics, LLC (“ASTATIC”) hereby warrants that this product will be free of defects in material and workmanship for a period
of two years from the date of purchase. In the unlikely event a defect occurs ASTATIC will, at its option, either repair or replace with
a new unit of equal or greater value. You should retain proof of purchase to validate the purchase date and return it with any warranty
claim. Return warranty claims carefully packed, insured and prepaid to the Service Department at the address listed below.
This warranty excludes exterior finish or appearance, damage from abuse, misuse of the product, use contrary to ASTATIC’s
instructions or unauthorized repair. All implied warranties or merchantability or fitness for a particular purpose are hereby disclaimed
and ASTATIC hereby disclaims liability for incidental, special or consequential damages resulting from the use or unavailability
of this product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not
allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so
the above exclusions and limitations may not apply to you.
Note: No other warranty, written or oral is authorized by Omnitronics, LLC
p/n 46873-29-00 rev2 10/27/08