Azden 35HT Microphone User Manual


  Open as PDF
of 4
 
4 1
Thank you for purchasing Azden’s 325 wireless microphone system. Depending o
n
which system you ordered this package will contain one or more of the following compo
-
nents: the 325UPR receiver, the 35BT body-pack transmitter with EX-503L lavalier mi
-
crophone, the 35XT XLR plug-in transmitter and/or the 35HT handheld microphon
e
transmitter. This equipment is designed primarily for video cameras but is usable wit
h
most electronic components having a microphone level input. The 325UPR allows you t
o
“receive” audio from two different transmitters at the same time.
RECEIVER (325UPR)
(1) Remove the battery compartment lid by sliding it down.
(2) Insert two fresh Alkaline* “AA” batteries into the compartment. Make sure the battery
polarity is correct as marked inside the battery compartment.
*Alkaline batteries are preferred, but you can use Azden’s 1HR-3U rechargeable Ni-MH batteries.
(3) POWER:
Switches the receiver “ON” or “OFF”.
(4) MIC OUT jack:
The 325UPR is supplied with both a mini-to-mini and a mini-to-dual XLR cable.
For mini jack microphone inputs: Use the supplied mini-to-mini cable. Plug one
end of the cable into the receiver and the other end of the cable into the micro-
phone input of the video camera.
For 3-pin XLR microphone inputs: Use the supplied mini-to-dual XLR cable. Plug
the mini-plug end of the cable into the receiver (use the screw-down sleeve to se-
cure it to the receiver) and plug the XLR ends of the cable into the microphone
inputs of the video camera. Ch.1 is on the “Tip” while Ch.2 in on the “Ring”.
(5) LCD Display:
The twin LCD display will light up when the power is turned “ON”. The LCD displays
show the following information.
TV:Receive Channel Number: 30:01 – 33:47
Battery Condition: Using a 3-step indicator - 1 (Low) to 3 (High)
Reception Level: Using a 4-step indicator - 1 (Low) to 4 (High)
To change the TV:Receive channel number, use the tip of the tool provided and press
the UP or DOWN button until the desired channel number appears (refer to included
chart). Once the desired TV:Receive channel number has been selected on the receiver,
set the transmitter to the same number.
The TV:Receive channel display is made of two parts. The first number is the actual TV
channel (30-33) and the second is the “receive channel” number (01-47)
Once the microphone is plugged into the 35XT the locking ring should be rotated
clockwise until snug. To remove the microphone, first rotate the locking ring
counterclockwise and then, while pressing the XLR release, pull the microphone
away from the 35XT.
(21) MIC Input LEVEL Control:
The MIC input LEVEL control enables you to adjust the input level of the connected
microphone. Using the supplied tool, turn the dial clockwise to increase, or
counterclockwise to decrease the input level.
(22) LCD Display:
This display shows the following information:
TV:Transmit Channel Number: 30:01 – 33:47
Battery Condition: Using a 3 step indicator - 1 (Low) to 3 (High)
To change the TV:Transmit channel number: Use the tip of the tool provided and press
the UP or DOWN button to the desired channel, number appears (refer to the included
chart). Once the desired TV:Transmit channel number has been selected on the
transmitter, set the receiver to the same number.
The TV:Transmit channel display is made of two parts. The first number is the actual TV
channel (30-33) and the second is the “transmit channel” number (01-47).
HANDHELD MICROPHONE/TRANSMITTER (35HT)
(23) Remove the battery compartment cover by rotating it counterclockwise and sliding it
down.
(24) Insert two fresh Alkaline* “AA” batteries* into the compartment. Make sure the battery
polarity is correct as marked inside the battery compartment.
*While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries.
In the battery compartment you will also find #25 and #26:
(25) MIC LEVEL Control:
The MIC LEVEL control enables you to adjust the audio level of the microphone. Using the
supplied tool, turn the dial clockwise to increase, or counterclockwise to decrease the
microphone’s audio level.
(26) UP/DOWN Channel Buttons:
To change the channel number, use the tip of the tool provided and press the UP or DOWN
button until the desired channel number appears. Once the desired channel number has
been selected on the transmitter, set the receiver to the same channel number.
 previous