Filter
Top Products
5
EURORACK UBB1002
1. INTRODUCTION
1.3 Control elements
1.3.1 Interface panel
Use this balanced XLR jack to connect a microphone to the
UBB1002 (applies to channels 1 through 7/8).
+ The phantom power required for condenser mics
can be activated with switch
. Please note that
in battery-operated mode the phantom power
provided is only +18 V!
Channels 1 and 2 feature an additional LINE input on a
balanced 1/4" jack.
The INSERT jack allows you to insert, for example, a
compressor or equalizer in the mono channels.
These are the two balanced LINE inputs on 1/4" jacks for
the left and right sides of the stereo channels, which can
be used in parallel to the microphone inputs.
Use the TAPE OUT jacks to connect, for example, a tape
deck for recording applications.
The TAPE IN jacks (on stereo RCA and 1/4" jacks) allow
for the connection of play-back devices such as CD players,
etc. Use either the RCA or the 1/4" jacks.
Use the PHONES jack to connect a commercially available
pair of headphones.
These are the balanced 1/4" jack MAIN OUTPUTS of your
UBB1002 that can be used to drive, e.g. a power amplifier.
The MON SEND connector provides the monitor signal of
your UBB1002, for example, to control a monitor amplifier
or active monitor speaker.
Connect the FX SEND connector to the input of an external
effects device.
+ The UBB1002 has no dedicated FX Return
connectors. However, you can connect the outputs
of an external effects device to the 1/4" jack inputs
of the stereo channels or channels 9/10. In this case,
the stereo channels FX control must be set to -oo
to avoid any feedback problems.
1.3.2 Front panel
The mono channels 1 and 2 of your UBB1002 feature the
same control elements. Therefore, the following description of
channel 1 also applies to channel 2.
The GAIN MIC control determines the channels input gain,
both for a microphone connected via the XLR jack and for
other signal sources connected to the 1/4" jack. Adjust the
signal gain so that the Clip LED below the control lights up
during peak signal only, but never permanently. In battery-
operated mode the Clip LED is switched off.
Use the PAN control to adjust the signals position on the
stereo basis.
Your UBB1002 comes with a 3-band equalizer: the HI
control governs the high frequency range, the MID control
can be used to boost/cut the midrange frequencies, and
the LOW control allows you to raise or lower the gain of
the bass range.
The CHANNEL fader adjusts the volume of the
corresponding channel.
Use the MON control to determine the channel volume sent
to the monitor mix bus. When set fully to the left, the channel
volume in the monitor mix is zero.
The FX control adjusts the effects volume for the
corresponding channel.
The stereo channels 3/4, 5/6, and 7/8 differ from channels
1 and 2 not only with regard to the connectors provided. They
also have two GAIN controls, i.e. you can connect a
microphone and a stereo line signal at the same time!
+ When you connect a microphone to a stereo channel
on the UBB1002, the input gain is governed by the
GAIN MIC control!
The GAIN LINE control is used to adjust the line input gain.
Here, too, the signal can be monitored visually with the Clip
LED.
The BAL control performs two functions: When you connect
a microphone via the XLR connector, or another signal
source via the L/MONO jack, the BAL control determines
the signal position on the stereo basis. When both 1/4" jack
inputs (L & R) are used, the BAL control adjusts the volume
balance of the two sources connected.
Except for the GAIN MIC control and a different set of
connectors, the channels 9/10 feature the same control elements
as the stereo channels. See
& and through .
1.3.3 Main section
The LEVEL DISPLAY reads the output level of your
UBB1002. Make sure that the two Clip LEDs wont light up.
Use this switch to activate the phantom power required
for condenser microphones. In battery-operated mode the
phantom power provided is only +18 V!
The MON SEND control adjusts the volume level of the
monitor signal provided at connector .
Use the MASTER fader to set the overall volume level of
your UBB1002.
The FX SEND control allows you to adjust the level that is
sent to an external effects device via connector . Thus,
you can drive all types of effects devices without any risk
of distortion.
The PHONES control governs the headphones volume.
Connect the enclosed power supply to the AC POWER IN
jack.
Use the POWER ON switch to switch on your UBB1002,
which is indicated by the LED below the LEVEL DISPLAY
.
SERIAL NUMBER. Please take the time to have the warranty
card filled out completely, and return it within 14 days after
the date of purchase, so as to be entitled to benefit from
our extended warranty. Or use our online registration option
available on the World Wide Web at www.behringer.com).