Filter
Top Products
GLX30
Guitar Amplifier with
DSP
1 2 3 4 5 6 7 8 9 10 12 13 14 1511
1: INPUT: Use this 1/4” jack to connect your guitar to
the amplifier by means of a shielded instrument cable.
SOLO CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
2: GAIN: Use this control to adjust the amount of dis-
tortion for the Solo channel.
3: SHAPE: Use this control to adjust to tone of the
Solo channel.
4: LEVEL: Use this control to adjust the output level
of the Solo channel.
5: SOLO/CLEAN: Use this switch to select the Solo
or Clean channel. With the switch in the out position,
the Clean channel is selected. When the switch is
depressed, the Solo channel is selected.
CLEAN CHANNEL: A normal gain channel designed
to give you crystal clear sounds to medium distortion.
6: LEVEL: Use this control to adjust the output level
of the Clean channel.
7: LOW: Use this control to adjust the low frequency
level of the clean channel.
8: MID: Use this control to adjust the midrange fre-
quency level of the clean channel.
9: HIGH: Use this control to adjust the high frequen-
cy level of the clean channel.
10: DSP LEVEL: Use this control to adjust the level of
the selected digital effect. The DSP effects can be
turned on and off by using a footswitch (#16, rear
panel).
11: DSP MODE: Use this control to select one of the
16 built-in digital effects. The numbers around the
control correspond to the digital effects as listed in the
chart below.
12: CD INPUT: Use these RCA jacks to connect the
output from a CD payer or tape deck to the amplifier.
The signal at these jacks is summed into a mono sig-
nal which is sent to the internal power amp circuit.
Use the CD or tape player’s output level control to
adjust the signal for the proper mix with your guitar.
13: HEADPHONES: Use this jack to connect head-
phones to the amplifier. The internal speaker is dis-
connected when headphones are used.
CAUTION: To avoid possible damage to your
hearing, do not use headphones for extended
periods of time at extremely loud levels.
14: SPEAKER: Use this jack to connect the amplifier
to an external speaker. The internal speaker is dis-
connected when this jack is used. The impedance of
the external speaker must be 4 ohms or greater.
WARNING: Do not attempt to use headphones in
the Speaker jack! Permanent hearing damage
could result!
15: POWER: Use this switch to turn the amplifier on
(top of the switch depressed) and off (bottom of the
switch depressed). The adjacent LED illuminates
when the amplifier is turned on.
16: FOOTSWITCH (rear panel, not shown): Use this
jack to connect the 1/4” stereo plug on the cable of a
two-button footswitch (such as the Crate CFP2. This
allows you to remotely switch between the Clean and
Solo channels and turn the DSP function on and off.
17: POWER CORD (rear panel, not shown): The
grounded power cord should only be plugged into a
grounded power outlet that meets all applicable electri-
cal codes and is compatible with the voltage, power, and
frequency requirements stated on the rear panel. Do not
attempt to defeat the safety ground connection.
1 - Small Room Reverb
2 - Medium Room Reverb
3 - Large Room Reverb
4 - Concert Hall Reverb
5 - Short Slapback with Small Room Reverb
6 - Medium Delay with Plate Reverb
7 - Long Delay with Large Room Reverb
8 - Slow Deep Flange with Reverb
9 - Flange with Reverb and Delay
10 - Slow Tremolo Chorus With Reverb
11 - Chorus with Reverb and Delay
12 - Rotating Speaker
13 - Octave Divider
14 - Touch Wah
15 - Inverse Wah
16 - Doubler
The Front Panel:
The Digital Effects: