Crown Audio PZM-11LL Microphone User Manual


 
Crown International, Inc.
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL: 574-294-8000
FAX: 574-294-8FAX
www.crownaudio.com
©
2008 Crown Audio
®
, Inc. Specifi cations subject to change
without prior notice. Latest information available at www.
crownaudio.com. Crown, Crown Audio, PZM and Pres-
sure Zone Microphone are registered trademarks of Crown
International. Pressure Recording Process is a trademark of
E. M. Long Associates.
6/08 136455-6
PZM-11
PZM-11LL
3. This entire step is for the PZM-11LL only. The
PZM-11LL can be powered in three ways: 24V AC,
12-24V DC, or 12-48V phantom power. The mic
is factory-wired for 24V AC powering so that it is
compatible with video surveillance systems where
24V AC is readily available.
To use phantom power with the PZM-11LL: Put
R14 in R13’s space; put R15 in R16’s space (the
resistors are labeled on the circuit board). Note: In
some cases these resistors may be on the bottom
side of the board. Do not overheat. Then proceed
to step 4.
To use 24V AC or 12-24V DC with the PZM-11LL:
From your power source, run a twisted pair of
power cable to the ceiling or wall hole. Run the
power cable through the hole in the electrical box
(if any) and through either hole in the chassis (Fig.
4). Service the end of the power cable.
To use 24V AC with the PZM-11LL: Attach the
power leads to the screw terminals labeled 24V AC
INPUT.
To use 12-24V DC with the PZM-11LL: See
Fig. 5. Connect the positive lead from the DC
source to either screw terminal of the INPUT ter-
minal block. Connect the negative lead to the other
terminal of the INPUT terminal block.
4. Run the mic cable through the hole in the
electrical box (if any) and through either hole in the
chassis (Fig. 4). Service the end of the mic cable.
5. Attach your mic-cable leads to the screw termi-
nals labeled OUTPUT. Connect the mic-cable shield
to 1, audio + lead to 2, and audio – lead to 3. See
Figures 5 and 6.
6. Place the chassis over the two long screws.
Using the nuts provided, secure the chassis to the
faceplate.
7. Using the two screws provided, secure the
faceplate to the electrical box or wall board.
8. If you plan to use an XLR-type cable connector:
Solder the cable shield to pin 1, audio + lead to pin
2 and audio – lead to pin 3 of the XLR.
If you plan to use an RCA or phone connector:
Solder the cable shield to the long lug, and solder
the audio + lead to the tip or pin. Do not connect
the audio – lead because this may reduce the
output level in an unbalanced confi guration.
9. If the mic cable is run in metal conduit, ground
loops can occur that can cause hum. If hum is
present after installation, unsolder the chip resistor
labeled 000 on the printed-circuit board (R21 GND
LIFT in Fig. 5).
10. If you plan to use a cable connector, solder the
other end of the mic cable to a 3-pin professional
audio connector (XLR-type). Solder the cable
shield to pin 1, light-colored lead to pin 2, and
darker lead to pin 3.
If the PZM-11LL distorts, change resistor R5
labeled GAIN to increase headroom. Do not over-
heat. The surface-mount resistors listed below
are already on the circuit board. See Fig. 5.
1K minimum headroom
2K 6 dB more headroom
3.9K 12 dB more headroom
8.2K 18 dB more headroom
100K maximum headroom
(mic level)
Architects’ and Engineers’ Specifi cations
PZM-11
The microphone shall be the Crown Model
PZM-11. The microphone shall be a Pressure Zone
Microphone, electret-condenser type, with built-in
electronics interface. The microphone capsule
holder shall be mounted on a standard switch
plate. The microphone shall be powered from
12-48V phantom power. The output shall be low
impedance balanced. Frequency response shall be
from 80 Hz to 20,000 Hz. Low frequencies below
the voice range shall be rolled off. Open-circuit
sensitivity shall be 5 mV/Pa (–46 dB re 1V/Pa).
Maximum SPL capability shall be 120 dB SPL at
3% THD. Equivalent noise shall be 26 dBA typical
(0 dB = .0002 dyne/cm
2
). The Crown model PZM-
11 microphone is specifi ed.
PZM-11LL
The microphone shall be the Crown model
PZM-11LL. It shall be a Pressure Zone Micro-
phone, mountable in a wall or ceiling, and designed
not to look like a microphone. It shall have a line-
level output (1.4 V/Pa unloaded) and be powered
by 24V AC, 12-24V DC, or phantom power. The
frequency response shall be from 80 Hz to 20,000
Hz with a low-frequency rolloff to reduce rumble
and high-frequency boosdt for articulation. The
audio connector and power connector shall be
screw terminals. Output shall be balanced, low
impedance. The electret condenser transducer
shall have a hemispherical polar pattern when the
microphone is mounted in a wall or ceiling. The
Crown PZM-11LL microphone is specifi ed.
Warranty
Crown professional microphones are guaranteed
against malfunction for a period of three years
from date of original purchase. See enclosed war-
ranty sheet for additional information.
Service
If the unit fails to work, fi rst replace or repair
the mic cables and check the power supply.
Recheck your connections to the microphone
screw terminals. If service is required, return the
microphone and the electronic interface in its
original packaging to: Crown Factory Service,
1718 West Mishawaka Road, Elkhart, IN 46517-
9439. A Service Return Authorization (SRA) is
required for product being sent to the factory
for service. An SRA can be completed on line at
www.crownaudio.com/support/factserv.htm. For
further assistance or technical support call 800-
342-6939.
Fig.5. PZM-11LL DC Powering and Output Wiring
Fig. 3.
Wiring for Phantom Power
Fig. 4. PZM-11LL Wiring for 24V AC or
12-24V DC
Fig.6.
PZM-11 Output Wiring
GAIN
GND
LIFT
R5
GND 1
AUDIO – 3
AUDIO + 2
12 to
24VDC
GND 1
AUDIO – 3
AUDIO + 2
OUTPUT
SCREW
TERMINALS