Filter
Top Products
5
ENGLISH
@0 RESET switch
• Returns to initial settings when this switch is pressed.
@1 HEADPHONE output jack
• Accepts 1/4” stereo headphone plugs.
@2 HEADPHONE level control
• Adjusts the volume for the headphones.
@3 HEADPHONE mode button
• In the STEREO mode, this button feeds STEREO
Program and Cue to both earcups, in the MONO
mode, the Headphone circuit provides MONO Cue to
the left ear and MONO Program to the right.
• In the STEREO mode, the meter indicates the stereo
level in the LEFT and RIGHT Main Outputs. In the
MONO mode, mono CUE level is displayed on the
Left meter and mono PROGRAM level is displayed on
the Right meter.
• In the MONO mode, the adjacent green indicator
lights.
@4 HEADPHONE PAN control
• Serves two purposes…In the STEREO mode it
changes the relative levels of the Cue and Program
mixed together in both earcups. In the MONO mode it
changes the balance between the Mono Cue in the
left ear cup and the Mono Program in the right.
@5 CUE buttons
• Pressing in any or all of the CUE buttons routes the
respective Source to the Headphone and Meter Cue
sections. Pressing multiple buttons makes it possible
to derive mixed sound from the selected sources. The
adjacent red indicator illuminates when the button is
depressed.
@6 CROSSFADE ASSIGN A, B switches
• Assigns the Crossfader to any of the four Input
Channels and Off.
OFF
Select when not using the crossfader.
1 to 4
Select what channels (CH-1 to CH-4) to assign to A
and B.
Channels not assigned to A or B are output without
passing through the crossfader.
@7 CROSSFADER
• Controls the relative output level from the summed A
and B Mixes. When the fader is at its far left, only the
A Mix is heard from the Outputs. As the fader is
moved toward the right, the amount of B Mix is
increased and the amount of A Mix is decreased.
When the fader is centered, equal amounts of A and B
Mixes are routed to the Outputs. Fully right is all B Mix
at the Outputs.
@8 CROSSFADER CONTOUR control
• Allows adjusting the “shape” of the Crossfader
response from a gentle curve for smooth, long running
fades, to the steep pitch required for top performance
cut and scratch effects.
@9 CROSSFADER START A, B buttons
• The function to start the performance of CD Player
with Crossfader automatically is turned on/off.
• When the button is pressed in, the Crossfader Start is
on and the adjacent orange indicator lights.
#0 X-EFFECT function buttons
• The Fader Start is executed by connecting the
Expansion Jack of the RC of the DN-2100F and the
DN-2600F, the item that is executed by Crossfader
and Ch. fader are selected by the button in each Ch..
It is not possible to use when the RC is not connected.
SAMP. buttons
This function will start the Sampler of the DN-2600F
by using Crossfader and Ch. fader are turned on/off.
H/S BRAKE buttons
This button provides 2 functions, Brake and Platter-S.
You first need to load a Hot Start(s) to activate this
feature.
By pressing either H/S Brake button once, will activate
H/S Brake mode (orange indicator is lit) .
By pressing the same button once more, this will
activate H/S Platter-S mode (indicator is flashing).
A third press will turn this function OFF.
See “X-EFFECT” to use this feature on page 8.
H/S 1, 2 buttons
This function will start the Hot Start of the DN-2100F
and the DN-2600F by using Crossfader and Ch. fader
are turned on/off.
#1 CH. FADER START switches
• This function will start the performance of CD Player
with Ch. fader automatically is turned on/off.
#2 POWER indicator
• When the red indicator is lit, the DN-X800 is ready to
go.
(2) Rear Panel
#3 POWER switch
• Press the switch to turn the power on.
#4 MAIN OUT (BALANCED) connectors
• These XLR type connectors provide a balanced line
level output.
• Connect these connectors to the balanced analog
input connectors on an amplifier or console.
• Pin layout 1. Common 2. Hot 3. Cold
• Applicable connector: Cannon XLR-3-31 or equivalent.
NOTE:
Do not short-circuit the hot or cold pin with the common
pin.
#5 MAIN OUT (UNBALANCED) jacks
• This stereo pair of RCA jacks provide a unbalanced line
level output.
• Connect these jacks to the unbalanced analog input
jacks on an amplifier or console.
#6 DIGITAL OUT 1, 2 jacks
• These RCA jacks provide a digital output data. The
signal is unaffected by the Master Level fader. Output
is controlled by Ch. fader volume.
• We recommend using a 75Ω/ohm RCA cord for best
digital transfer. (available from any audio/video retailer)
#7 ZONE OUT (BALANCED) connectors
• These XLR type connectors provide a balanced line
level output with independent front panel Zone Level
controls and are not affected by the Master Level
control.
• Connect these connectors to the balanced analog
input connectors on an amplifier or console.
• Pin layout 1. Common 2. Hot 3. Cold
• Applicable connector: Cannon XLR-3-31 or equivalent.
NOTE:
Do not short-circuit the hot or cold pin with the common
pin.
#8 BOOTH OUT jacks
• This stereo pair of RCA jacks provide a unbalanced line
level output with independent front panel Booth Level
controls and are not affected by the Master Level
control.
• Connect these jacks to the unbalanced analog input
jacks on an amplifier or console.
#9 X-EFFECTS JACK
• Connect this jack to the remote of the DN-2100F and
the DN-2600F using the 3.5 mm stereo mini cord.
$0 SUBWOOFER output jack
• This 1/4” mono jacks provide a mono line level output
of Main Out. The signal is affected by the Master
Level fader.
• Connect this jacks to the subwoofer input jack on an
amplifier.
$1 TAPE OUT jacks
• This stereo pair of RCA jacks provide a line level
output. The signal is unaffected by the Master Level
fader. Output is controlled by Ch. fader volume.
• It is intended for use with a tape recorder, but is not
restricted to that purpose. Output is controlled by Ch.
fader volume.
$2 EFFECT jacks
• These 1/4” stereo jacks allow stereo external
processing of the Program signal.
• These are switching jacks --- always complete the loop
when connecting a send and return, or no sound will
be heard.
$3 DIGITAL 1, 2, 3, 4 input jacks
• These RCA jacks are Inputs for any digital output
device.
• We recommend using a 75Ω/ohm RCA cord for best
digital transfer. (available from any audio/video retailer)
$4 LINE 2, 4, 6, 7, 8 input jacks
• These stereo pairs of unbalanced RCA jacks are Inputs
for any line level device.
$5 Ch 3, 4 FADER output jacks
• Connect these jacks to the Fader input jacks of the
DN-1800F, the DN-2100F and the DN-2600F using the
3.5 mm stereo mini cord.
$6 PHONO 1, 2, 3 / LINE 1, 3, 5 input jacks
• These stereo pairs of unbalanced RCA jacks are Inputs
for a Phono (RIAA) stage for magnetic (MM) cartridges
or a Line stage suitable for any device, such as a CD
player.
$7 PHONO 1, 2, 3 / LINE 1, 3, 5 switches
• These switches change the Input from Phono to a
Line level inputs.
• These switches set a Line level inputs when Turntable
is not connected.
$8 Phono Ground screw
• This screws provide a place to connect the ground
wire from a turntable.
This terminal is exclusively for a turntable grounding
and not a safety earth ground.
$9 MAIN MIC input connector
• Neutrik combo jack.
• Accepts either a balanced microphone with an XLR
connector or an unbalanced microphone with 1/4”
mono jacks.
%0 AUX MIC input jack
• Accepts an unbalanced microphone with 1/4” mono
jacks.