Filter
Top Products
DD
DD
ee
ee
ll
ll
uu
uu
xx
xx
ee
ee
™™
™™
99
99
00
00
00
00
6
Your new Deluxe™ 900 amplifier delivers world–class Fender
®
tone and world–standard Fender
®
DSP technology:
• 90W output power @ 4 ohms
• Seven Timbre filters for total tone control
• Digital Signal Processing
• 16 FX SELECTIONS
• Separate FX LEVEL and TIME/RATE controls
• Selectable Normal and Drive channels with independent
volume and tone controls
• Selectable Drive 1 and Drive 2 channels for two independently
adjustable distortion channels.
• PRE AMP OUT and POWER AMP IN jacks
•
• Built in Tuner
• 3-button FOOTSWITCH (included) enables remote activation of:
(1) Channel Select, (2) Drive Select, (3) Effects
Thank you for choosing Fender
Thank you for choosing Fender
®
®
The W
The W
orld’
orld’
s most popular instr
s most popular instr
ument amplifiers—since 1946
ument amplifiers—since 1946
A. INPUTS - Plug-in connection for your guitar.
B. VOLUME - Adjusts the loudness of the Normal channel.
C. TREBLE / MIDDLE / BASS - Adjusts the high–, middle– and
low–frequency tone of the Normal channel.
D. CHANNEL SELECT -
OUT Normal channel {B–C}
IN Drive channels {E–J}
E. DRIVE 1 - Adjusts the distortion level of the Drive 1 channel.
F. VOLUME 1 - Adjusts the overall loudness of the Drive 1
channel.
G. DRIVE SELECT - Press CHANNEL SELECT {D} in to
activate DRIVE SELECT.
OUT Drive 1 channel {E–F, J}
IN Drive 2 channel {H–I, J}
H. DRIVE 2 - Adjusts the distortion level of the Drive 2 channel.
I. VOLUME 2 - Adjusts the overall loudness of the Drive 2
channel.
J. TREBLE / MID / BASS - Adjusts the high–, middle– and
low–frequency tone of the Drive channels.
K. TIMBRE - Press repeatedly to select an amp character as
indicated by the LEDs. Your selection is stored and
automatically activated for each channel (Normal, Drive 1,
Drive 2).
TIMBRE FILTERS: These pre-set Equalizer curves allow the
Dyna–Touch amps to create seven very different voices on
each channel. FLAT—Preamp and Power Amp signal
without further equalization. BRIGHT—Treble boost,
especially effective for brightening the tone of double–coil
pickups. DARK—Treble cut, especially effective for
traditional Jazz tones with the Normal channel. DEEP—
Bass boost, especially effective for beefing up the tone of
single–coil pickups. SCOOP—A severe low–mid scoop with
bass boost designed for modern distortion tones.
SQUAWK—A strong mid peak reminiscent of a partially
depressed Wah–Wah pedal; great for distorted solos that
need to cut through the mix. ACOUSTIC—Simulates the
sound of an acoustic–electric guitar with extreme high treble
boost and bass boost; best with the Normal channel. Note:
This much Timbre flexibility requires that you use a little
common sense! It is possible to get “too much of a good
thing,” such as undesirable treble harshness or bass
boominess depending on your particular guitar, playing style
and knob settings.
L. TUNER - Activates the tuner and mutes audio output. Strike
a string and the top row of LEDs indicate the nearest note.
Sharp/flat notes are indicated by two LEDs; for example, A
and B light up to indicate A sharp (B flat). The bottom row
of LEDs indicate fine tuning.
M. EFFECTS LEVEL - Adjusts the level of the active effect.
N. EFFECTS SELECT - Selects the active effect (see next
page).
O. TIME/RATE - Adjusts the interval length / modulation speed
of the active effect (see next page).
Rear Panel
P.
POWER SWITCH - Switches the amplifier
on / off.
Q. POWER CORD SOCKET - Connect the included
power cord in accordance with the voltage and
frequency ratings listed on the rear panel of your
amplifier.
R. PRE AMP OUT / POWER AMP IN -
Ef
fects Loop - Connect PRE AMP OUT to an effects device
input, then connect the effects device output to PWR AMP
IN.
Multiple Amps - Connect the primary unit’s PRE AMP OUT
to the auxiliary unit’s PWR AMP IN. The primary unit is used
to control all auxiliary units.
Recording or Reinforcement - Connect PRE AMP OUT to
the input jack of sound equipment.
Use TS (Tip-Sleeve) standard type plugs with
these jacks. The PRE AMP OUT signal includes
onboard tone shaping and DSP effects processing.
S. FOOTSWITCH - Connect the
3-button Fender footswitch (included) at
this jack to enable remote switching of
CHANNEL SELECT, DRIVE SELECT,
EFFECTS. When plugged in, the footswitch buttons
override the corresponding front panel controls.
PP
PP
aa
aa
nn
nn
ee
ee
ll
ll
FF
FF
uu
uu
nn
nn
cc
cc
tt
tt
ii
ii
oo
oo
nn
nn
ss
ss
wwwwww
..
ffeennddeerr..ccoomm
✧
wwwwww
..mmrrggeeaarrhheeaadd..nneett