Filter
Top Products
Page 4
1. Unscrew the outside FADER PLATE SCREWS (B). Do
not touch the INSIDE SCREWS (C).
2. Carefully lift the fader and unplug the CABLE (D).
3. Plug the new fader into the cable and place it back in the
mixer.
4. Screw the fader to the mixer.
5. KILLING FREQUENCIES: There are two ways to kill frequencies,
using the LOW, MID and HIGH KILL SWITCHES (20, 21, 22) and
using the LOW, MID and HIGH ROTARY CONTROLS (16, 17, 18).
When the selected KILL SWITCH is activated the LED will light and
the frequency will be killed. When the selected ROTARY CONTROL
is turned all the way to the left, the frequency will be killed. You can
also use the ROTARY CONTROLS to boost frequencies up to +12
dB. The normal setting for the ROTARY CONTROLS is zero.
SUGGESTION: You can use the Kill Features on each channel to
remove Low, Mid and/or High bands for a smoother mix and mix
frequencies from both channels to create special effects.
6. PUNCH IN: The PUNCH IN BUTTON (23) allows you to add a
channel’s signal to the mix when the crossfader is set to the opposite
channel.
7. PUNCH OUT: The PUNCH OUT BUTTON (24) allows you to remove
a channel’s signal from the mix when the crossfader is set to that
channel.
SUGGESTION: Keep the crossfader in the center and use the
punch in and punch out of both channels together to create scratch
type effects.
8. LOOP SECTION: To activate loop, press the LOOP BUTTON (25)
and the LOOP LED (26) will light. When the LOOP LED is lit, any
device connected to the LOOP OUTPUT (38) and INPUT (37) jacks
will be inserted into the signal path.
9. OUTPUT CONTROL SECTION: The level of the AMP OUT (34) is
controlled by the MASTER (27) control. The BOOTH (28) control
adjusts the level of the BOOTH OUTPUT (35). HINT: The booth
OUTPUT is used by some DJs to run monitor speakers in their DJ
booth. You can also use it as a second ZONE or AMP output.
NOTE: The RECORD OUT (36) has no level control. The
level is set by the channel slides and the gain controls of
the selected channel. The tonal qualities are set by the
bass, treble and mid controls of that same channel.
10. TALKOVER SECTION: The purpose of the talkover section is to allow
the program playing to be muted so that the mic can be heard above
the music. The MIC/TALKOVER SWITCH (4) has three settings.
When the MIC/TALKOVER SWITCH (4) is in the bottom position, the
mic and talkover are both off. When the MIC/TALKOVER SWITCH
(4) is in the center position the mic is on, the MIC INDICATOR (5) will
glow, but talkover is off. When the MIC/TALKOVER SWITCH (4) is in
the top position, the mic and talkover will be on and the volume of all
sources except the Mic input are lowered by 16 dB. The TREBLE (6),
BASS (7), and LEVEL (8) controls allow you to fully adjust the mic
signal.
11. CUE SECTION: By connecting a set of headphones to the
HEADPHONE (9) jack, you can monitor either channel or both. Select
the Channel I by sliding the CUE SLIDER (29) control to the left or
Channel II by sliding the CUE SLIDER (29) control to the right. Use
the CUE LEVEL (30) control to adjust the headphone volume without
effecting the overall mix.
12. DISPLAY: The dual function DISPLAY (31) indicates either the
MASTER OUTPUT (34) left and right levels or the channel I and
channel II levels. You can choose the option you want by pressing the
DISPLAY (32) button.
NOTE: When the DISPLAY (31) is in the channel I/channel II
display mode, by adjusting the individual channel gain and
tone controls, you can increase or decrease the signal to
match the other channels signal. The channel slides and
crossfader have no effect on the display readings.
Specifications
INPUTS:
DJ Mic....................................................1.5mV 2Kohm balanced
Phono.........................................................................3mV 47Kohm
Line.......................................................................150 mV 27Kohm
OUTPUTS:
Amp/Booth......................................................0 dB 1V 400ohm
Max..............................24V Peak to Peak
Rec...........................................................................225mV 5Kohm
MIC:
Bass......................................................................................± 12dB
High.......................................................................................± 12dB
GENERAL:
Bass (Channels I - II)........................................................+ 12dB/Kill
Mid (Channels I - II).........................................................+ 12dB/Kill
Treble (Channels I - II).....................................................+ 12dB/Kill
Gain (Channels I - II)...........................................................0 to -20dB
Frequency Response....................................20Hz - 20KHz +/- 2dB
Distortion................................................................................0.02%
S/N Ratio...............................................................better than 80dB
Talkover Attenuation..............................................................-16dB
Headphone Impedance.........................................................16ohm
Power Source.............................................115/230V 50/60Hz 10W
Dimensions...........................................10”w x 4 5/8”h x 14”d
Weight........................................................................8.3 lbs.