Filter
Top Products
9. CROSSFADER SECTION: The CROSSFADER (38)
allows you to mix from one source to another. The CH 2
(28) is controlled on the LEFT side of the CROSSFADER
(38). CH 3 (31) is controlled by the RIGHT side of the
CROSSFADER (38). CH 1 (25) and CH 4 (34) are con-
trolled through their respective SLIDE CONTROLS (25,
34) and not the CROSSFADER (38). The CROSSFADER
(38) in your unit is removable and if the need arises can
be easily replaced. Your Gemini mixer comes with an RG-
45 PRO (RAILGLIDE™) Dual-Rail Crossfader. Rail
Glide™ crossfaders have internal dual stainless steel
rails that allow the slider to ride smoothly and accurately
from end to end. Also available is our CF-45 PRO
(PROGLIDE™) Dual-Rail Crossfader. This unique
crossfader features, state of the art conductive plastic
technology, for unlimited useage. Another crossfader we
have available is the PSF-45 (PRO SCRATCH™) cross-
fader with a special curve designed for scratch mixing.
Just purchase one from your Gemini dealer and follow the
instructions:
10. MIC SECTION: Plug your main mic into the MIC 1 XLR
INPUT (15) located on the top panel. The rotary controls
for HIGH (18) and LOW (19) for MIC 1 (15) allow you to
adjust the tone of MIC 1 (15). The MIC 1 ROTARY VOL-
UME CONTROL (17) above the HIGH(18)/LOW(19) con-
trols adjust the decibel level of MIC 1 (15). You may also
plug a second mic into the rear panel at the MIC 2 ¼"
JACK (14). The tone and decibel level of MIC 2 (14) is
controlled by the CH 1 SLIDE (25) and the 5 BAND EQ
(35).
11. TALKOVER: The purpose of the TALKOVER MODE is
to allow the program playing to be muted so that the mic
may be heard above the music. The MIC/TALKOVER
SWITCH (16) controls MIC 1 (15) with 3 settings:
- When the MIC/TALKOVER SWITCH (16) is in the BOT-
TOM position,
MIC 1 (15) and TALKOVER MODE are all
OFF.
- When the MIC/TALKOVER SWITCH (16) is in the CEN-
TER position, MIC 1 (15) is ON and TALKOVER MODE
is OFF. The MIC ON LED INDICATOR glows when MIC
1 (15) is ON.
- When the MIC/TALKOVER SWITCH (16) is in the TOP
position, MIC 1 (15) is ON and TALKOVER MODE is ON,
and the volume of all sources except MIC 1(15) inputs is
lowered by -16 dB.
12. VU METER: The VU METER (37) indicates the pro-
gram output level of the MASTER (2) left and right stereo
levels.
SPECIFICATIONS:
INPUTS:
MIC 1..............................................1.5mV 1kOhm Balanced
MIC 2.............................................1.5mV 1KOhm Balanced
Phono.............................................................3 mV 47kOhm
Line.............................................................150 mV 10kOhm
OUTPUTS:
Amp............................................................0 dB 1V 400Ohm
Max...........................................................20V Peak to Peak
Rec................................................................225mV 5kOhm
GENERAL:
5 Band EQ..................................................................± 12dB
Frequency Response.........................20Hz - 20KHz +/- 2dB
Distortion....................................................Less Than 0.02%
S/N Ratio...................................................Better Than 80dB
Talkover Attenuation.....................................................-16dB
Power Source.............................Adapter-115V/15V AC 0.5A
................................................................ 230V/15V AC 0.5A
Unit Dimensions...................................W 19" x H 3.4" x D 7"
...............................................................(483 x 76 x 178mm)
Weight........................................................7.04 lbs (3.19 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION
FOR IMPROVEMENT.
Replaceable Crossfader
1. Unscrew the outside FADER plate screws (B).
- Do not touch INSIDE SCREWS (C).
2. Carefully remove old
Crossfader and unplug
CABLE (D).
3.Plug new Crossfader into
CABLE (D) and place
back into mixer.
4. Screw Crossfader to
mixer with the FADER
PLATE SCREWS (B).
(5)