Filter
Top Products
|
35
ProKeys Sono 88 User Guide
Pedal Assignment
The Sustain pedal can be assigned to send standard MIDI CCs up to 127 and extended custom messages from 128 to 131.
The default for the Sustain pedal is sending MIDI Controller message 64. Use the G#5 key in Edit mode to change the MIDI
CC assignment for the Sustain Pedal.
To assign a MIDI controller message to the Sustain Pedal jack:
1. Press the Edit Mode button.
2. Press the black key above G5 (G#5), representing “Pedal Assign.”
3. Use the Numerical Data Entry keys G5 – B6 to enter the number of
the controller value you want to assign to the Sustain Pedal Jack.
4. Press C7 for “ENTER.”
If you make an error while entering the numerical data value, you can press the
CANCEL key (C3) to exit Edit mode without changing the MIDI CC assigned to
the Sustain Pedal jack.
To re-assign the Sustain Pedal jack to its default function:
1. Press the Edit Mode button.
2. Press the black key above G5 (G#5), representing “Pedal Assign.”
3. Press the F5 key (Default). When the Default key is pressed, the
parameter is reset to its default value, and Performance mode
resumes.
Knob Assignment
The Voice Volume knob can be assigned to any of 132 controllers (0-131) shown
at the back of this manual in Appendix C.
To assign a MIDI controller message to the Voice Volume knob:
1. Press the Edit Mode button.
2. Press the black key above A5 (A#5), representing “Knob Assign.”
3. Use the Numerical Data Entry keys G5 – B6 to enter the number of
the controller value you want to assign to the Voice Volume knob.
4. Press C7 for “ENTER.”
If you make an error while entering the numerical data value, you can press the
CANCEL key (C3) to exit Edit mode without changing the MIDI CC assigned to
the Voice Volume knob.
To re-assign the Voice Volume knob to its default function:
1. Press the Edit Mode button.
2. Press the black key above A5 (A#5), representing “Knob Assign.”
3. Press the F5 key (Default). When the Default key is pressed, the
parameter is reset to its default value, and Performance mode
resumes.
NOTE: Optional MIDI parameters assigned to the Voice Volume knob, Modulation wheel, or Sustain
Pedal jack are not stored when the keyboard is turned off. These parameters will reset to their
default values each time the keyboard is powered on.
TIP: Using the Modulation wheel or
Voice Volume knob to set the reverb
or chorus depth on ProKeys Sono
Changing Reverb Depth
The Modulation wheel and/or the Voice
Volume knob can be re-assigned to control the
depth of the built-in ProKeys Sono reverb. To
do this:
1. Press the Edit Mode button.
2. Press either the Wheel Assign (F#5) or
Knob Assign (A#5) key.
3.PressB6toenter“9.”
4. Press A5 to enter “1” so you have
entered “91.”
5. Press C7 for “ENTER.”
This setting can be undone by powering the
unit off and back on, or by using the Default
key as described in the next section.
CC 91 is the standard MIDI controller number
for reverb depth (see Appendix C).
Changing Chorus Depth
The Modulation wheel and/or the Voice
Volume knob can be re-assigned to control the
depth of the built-in ProKeys Sono chorus. To
do this:
1. Press the Edit Mode button.
2. Press either the Wheel Assign (F#5) or
Knob Assign (A#5) key.
3.PressB6toenter“9.”
4.PressC6toenter“3”soyouhaveentered
“93.”
5. Press C7 for “ENTER.”
This setting can be undone by powering the
unit off and back on, or by using the Default
key as described in the next section.
CC 93 is the standard MIDI controller number
for chorus depth (see Appendix C).