Multiquip WC-62P Music Mixer User Manual


 
PAGE 12 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)
WC-62P/S CONCRETE MIXER — GENERAL INFORMATION
Application
This mixer is
only
intended for the production of
concrete
.
The mixer must be used for its intended purpose and is not
suitable for the mixing of
flammable
or
explosive
substances. The mixer
must not be used
in an explosive
atmosphere. Use Table 4 (Mixing Hints) as a guide when
mixing concrete for various applications.
Power Plants
The MQ Whiteman WC-62P and WC-62S mixers can be
powered by a variety of power plants or an electric motor.
Refer to Table 2 to for specific engine or electric motor data
information. All engines are air-cooled, 4-stroke gasoline
engines.
Electrical
If mixer is equipped with an
electric motor
, make sure that
the power being supplied to the motor corresponds to the
voltage rating label on the motor. Supplying the wrong voltage
to the electric motor will cause severe electrical damage to
the motor.
Always make sure the
OFF/ON
switch on the electric motor
is in the
OFF
position before applying power.
It is
strongly recommended
when inserting the mixer's
power cord into a receptacle, that a G.F.C.I. (
Ground Fault
Current
Interrupter
) receptacle be used (115 VAC
applications).
Extension Cables
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. The wire
cross section must be a minimum of 2.5 mm
2
. Choose an
extension cord of adequate current carrying as Referenced
in Table 6. Remember
distance
affects the wire size of the
extension cable.
Ensure that the extension cable is carefully laid out avoid-
ing
wet areas
,
sharp edges
and locations where vehicles
might run over it. Avoid allowing the extension cable to be
trapped underneath the mixer.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn ex-
tension cable immediately.
Hardware
Check all hardware on the mixer before starting. Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. Use Table 3 as general
guideline when the torqueing of mixer hardware is required.
Remember to keep all mixer hardware components tight.
Engine Maintenance
For basic engine maintenance, refer to the engine maintenance
section in this manual. For a more detailed engine maintenance,
refer to the
Honda
or
Robin
Engine Owner's manual furnished
with the engine.
euqroTerawdraH.3elbaT
noitadnemmoceR s
erawdraH
retemaiD
)sbl-tf(euqroT
81xhcni-61/541
61xhcni-8/342
42xhcni-8/
373
31xhcni-2/193
31xhcni-2/1
)8edarG(
09
STNIHGNIXIM.4elbaT
SNOITACILPPA
XIM
SOITAR
SEITITNAUQHCTAB
HCTAB.XORPPA
TUPTUO
.sbl211TNEMEC
).sgK05(
gaB
DNASENOTS
.TF.UCRTL.TF.UCRTL.
TF.UCRTL
yranidrOtsoM
4:2:1GAB2/14/1-1532/1-2173 58
snoitadnuoF
6:3:1GAB3/14/1-1532/1-2174/3-287
ssaMhguoR
etercnoC
8:4:1GAB4
/14/1-1532/1-2174/3-287
,sroolFthgitretaW
.ctE,stiP,sknaT
3:2/1-1:1GAB3/24/1-1533173 58