Filter
Top Products
DM3000X/DM3002X
- The Leader in DJ Technology
©2001 Industries - 7 - http://www.numark.com
MIXER FEATURES
INPUTS
1. Input faders - control individual source levels in the mix.
2.
Input Toggle Switch (Transform) - selects which source will be live to
that channel based on what you have connected to the rear panel input
section. By removing the face panel the switch can be rotated into any
of eight positions.
3.
Pre-fader Gain Control – adjusts the pre-fader volume for cleaner
sound. Use this in conjunction with the PFL Meter to adjust the audio to
an optimum level.
4.
Channel EQ – adjusts the Treble, Middle, and Bass frequencies
respectively of the channel audio. Full rotation to the left creates a
“CUT” effect eliminating most of the sound from that frequency area.
5.
Process Loop (DM3002X only) – activates the external process loop to
the channel selected.
Note: All process loops go to the same output and return. By pressing
process on two channels at the same time, the audio will bleed through
to the each channel. Only use one process loop at a time!
6.
PFL Meter (DM3002X only) - used to adjust the PFL levels, accurately
match channel levels with the Pre-fader gain controls before mixing
them together. The idea is to properly match PFL inputs, not the input
with the stereo output meter!
MICROPHONE
7. Mic Gain Controls – controls the DJ Mic volume for the Neutrik™
“Combo” connector on the front panel.
8.
Treble and Bass Controls – for fine-tuning the tone of your voice on
both mics through the sound system. The controls are detented for
setting tone "flat". For best results, use a dynamic cardioid microphone.
9.
¼” input connector - allows connection of a 1/4” microphone jack
directly into the mixer.
HEADPHONE CUEING
10. Channel Cue Assign - are used to route Pre Fader Level (PFL) channel
audio to the Monitor Section. The channel faders do not control the
Cue volume.
11.
Headphone Mix - controls the mix of PFL and PGM signals to your
headphones. When the slider is moved to the left, all you will hear is the
cue source. When the slider is all the way to the right, you will hear what
is playing through the master output. By blending, beats can be matched
exactly and segues can be smooth when a song is cued.
12.
Headphone Level – adjusts cue volume.
13.
Split/Blend Cue – controls how PFL and Program audio are sent to your
headphones. In split mode, the PFL audio can be heard in your left ear
and PGM audio can be heard in your right ear. In blend mode, both PFL
and PGM can be heard in both ears.
14.
Headphone output – for your 1/4” or 1/8” headphones.
OUTPUTS
15. Master Fader – controls the overall output level.
16.
Panning - controls output to the left and right speakers. By rotating left
only the left speaker will be heard. By rotating right only the right
speaker will be heard.
CROSSFADER
17. Crossfader - achieves clean segues between the two input channels
selected by the Crossfader Assign.
18.
Crossfader Slope – determines how quickly the audio from the
opposing side of the crossfader activates. A tight curve (right position)
turns on the opposing audio signal with very little crossfader movement.
A loose curve (left position) makes very long and smooth segues in
transition.
19.
Hamster switch with Off position – reverses the direction of the
crossfader. In the center position the crossfader is deactivated.
20.
Crossfader Assign – channels 1 or 2 can be assigned to the left.
Channels 2 and 3 can be assigned to the right. If for example channels 1
and 3 were selected then "Hard left" selects Channel 1 and "Hard right"
selects Channel 3. With the crossfader centered, both assigned channels
are live. Use the crossfader for fast and seamless segues from one
selected channel to the other.
Note: If channel 2 is selected on both sides, the crossfader will turn off
channel 2 in the left position and turn it on in the right position
Note: The crossfader is user replaceable in case of failure. Simply
unscrew the two large screws that hold it in place, lift it out and
disconnect its cable. Re-attach the new crossfader and screw the
mounting plate back onto the unit - you’re back in business!
21.
Beat Lights – Indicate when strong bass beats are present to allow more
accurate beat mixes.
22.
Push Button transforms (DM3002X only)– By pressing these button
the crossfader channel will respond as determined by the transform
assign
23.
Transform Assign (DM3002X only):
(IN) - When active the transform button will punch in the channel
assigned regardless of crossfader position. When punching in the
opposing channel will be eliminated.
(OUT) – When active transform button will eliminate audio assigned
24.
KILL switches (DM3002X only)- By moving these toggle down or up
the marked frequency area will be removed. For instance is BASS is
pressed the bass beat will be removed, Highs might remove cymbals,
and middle might remove vocals.
25.
Fader Start (DM3002X only)– activates the crossfader to send play and
cue commands to your auto-start Numark CD player or other popular
brand. For fader start, attach your mixer to a remote start CD player
using industry standard 1/8”(3.5mm) cables. When you move the
crossfader toward the active channel, the attached CD player will start.
When it is moved away, that side will cue (similar to pressing the cue
button).
OTHER ITEMS
26. Stereo Auto Peak Hold Level Indicator- quickly and accurately tracks
level of audio output. The red LEDs show output overload. When using
as a master output meter, set the crossover, equalizer and power amp
inputs to avoid distortion at each step in the audio chain.
27.
Power Switch – Actives mixer power. Always turn on input devices
first, the mixer second, and amplifiers last!
28.
Light Connector – for attaching a 12V BNC style gooseneck light.