Filter
Top Products
FEATURES
• Four mic/line inputs with screw
terminals on each; two with XLR and
two with dual RCA phono jacks
• One dedicated 600 ohm transformer
balanced paging input with screw
terminals and rear panel screwdriver
adjust level control
• Two mute lines, providing internal
signal override or external switch
closure, with adjustable thresholds
and indicators
• Provisions for external master volume
control
• 24 volt (DC) phantom power
• Bass, Treble, and Contour EQ
controls
• Loop Out/Loop In patch point with
RCA phono connectors and link
switch
• Channel 4 output (RCA phono),
which gives a non-mutable output of
Channel 4
• AUX output for tape recorders, etc.
• Signal activity indicator
• Power indicator
• Low current 24 volt DC output
• SPS™ (Speaker Protection System)
circuitry with indicator
• 4 ohm, 8 ohm, 25 V and 70 V
transformer-isolated outputs (100 V
Export)
• 600 ohm balanced line level output
• AC convenience outlet
• Powder coated steel chassis
• Optional rack-mounting kits available
DESCRIPTION
The UMA
™
150T
II
is a versatile
mixer/amplifier designed for numerous
sound reinforcement applications. The
flexible input configurations make it an
excellent choice for paging and/or back/
foreground music systems. The UMA™
Series mixer/amplifiers are ready for
any job, utilizing an isolated transformer
with multiple output configurations.
ARCHITECTURAL &
ENGINEERING
SPECIFICATIONS
The mixer amplifier shall have four
microphone/line inputs and one
dedicated page input. Channels 1 and 2
shall have screw terminals and XLR
connectors for the Lo Z inputs; screw
terminals for the Hi Z inputs. Channels
3 and 4 shall have screw terminals for
the Lo Z inputs; screw terminals and
RCA phono connectors for the Hi Z
inputs. Channels 1 through 4 shall have
24 volt phantom power for the Lo Z
inputs. The page input shall be trans-
former balanced (600 ohms) and shall
have screw terminals for the input
connection.
The master section shall include one
master volume level control, two EQ
controls providing 10 dB boost or cut at
100 Hz and 10 kHz, and a "Contour"
switch providing 6 dB of boost at
100 Hz and 10 kHz.
Features and specifications subject to change without notice.
A Division of Peavey Electronics Corporation
711 A Street / Meridian, MS 39301 / U.S.A. / (601) 483-5376 / Fax 486-1154
©1994 #80302295 Printed in U.S.A. 3/96
The unit shall have two levels of
automatic muting. Mute 1 shall give
precedence to the page input, and it
shall override Channels 1 through 4,
with a threshold control on the page
input. Mute 2 shall give precedence to
Channel 1, and it shall override
Channels 2 through 4, with a threshold
control on Channel 1. The two mute
lines shall have screw terminals for
external mute control.
The unit shall have a Channel 4
output that provides an RCA phono,
non-mutable output of Channel 4.
Provision for an external master volume
control shall be made via screw
terminals.
The unit shall be packaged in a
rugged metal chassis 17" wide by
3-1/2" high by 15-5/8" deep. The unit
shall operate from standard 120 volts
AC, 60 Hz power. The internal power
amplifier shall be capable of delivering
150 watts into 4 ohms and 8 ohms, as
well as providing 25 volt and 70 volt
balanced line outputs. The unit shall be
capable of delivering rated power from
20 Hz to 20 kHz ±1.5 dB into 4 ohms at
its direct output at 0.5% or less distor-
tion with hum and noise at least 80 dB
below rated output from line level
inputs. The unit shall be called the
Peavey Architectural Acoustics Division
model UMA™ 150T
II
.
LIMITED WARRANTY
Peavey Electronics Corporation warrants to the original purchaser of this new Architectural Acoustics product that it is free from
defects in material and workmanship. If within one (1) year from date of purchase a properly installed product proves to be defective and
Peavey is notified, Peavey will repair or replace it at no charge. (Note: Batteries and patch cords not covered.) “Original purchaser” means
the customer for whom the product is originally installed.
Damage resulting from improper installation, interconnection of a unit or system of another manufacturer, accident or unreasonable
use, neglect or any other cause not arising from defects in material and workmanship is not covered by this warranty. The warranty is
valid only as to products purchased and installed in the United States and Canada.
THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE. UNDER NO CIRCUMSTANCES WILL PEAVEY BE
LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGES OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THIS LIMITED
WARRANTY IS THE ONLY EXPRESSED WARRANTY ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION, WAR-
RANTY, OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
Peavey’s liability to the original purchaser for damages for any cause whatsoever and regardless of the form of action is limited to
the actual damages up to the greater of Five Hundred Dollars ($500) or an amount equal to the purchase price of the product that caused
the damage or that is the subject of or is directly related to the cause of action. This limitation of liability will not apply to claims for personal
injury or damage to real property or tangible personal property allegedly caused by Peavey’s negligence. For information on service
under this warranty, call a Peavey customer service representative at (601) 483-5376.
U.S. Patent No. 5,509,080 for Bass Clipping Circuit
®
ARCHITECTURAL ACOUSTICS
®
TM
®