Filter
Top Products
Your PYLE PRO Series Performance Mixer
is a sophisticated control center, perfect for mixing sound from multiple playback sources such as
microphones, tuners, CD players, turntables or the audio outputs from a VCR. This mixer is ruggedly
constructed for home or professional use. Wide range volume controls permit you to adjust sound levels
accurately to achieve just the right mix for playing through your speaker system or for recording.
Please read this manual thoroughly before you attempt to set up and use the mixer. It contains a
range of suggestions and instructions to insure safe usage. Set up and used properly, you can expect
years of trouble-free service from this product.
Input/Output Features: all models
Ground Screw
for turntables
Features and Controls: PYD1919 Mixer
Pyle Pro Mixer Owner’s Manual – 1i – Pyle Pro Mixer Owner’s Manual
Owner’s Manual Table of Contents
Input/Output Features
Features and Controls: PYD1919
Features and Controls: PYD1929
Features and Controls: PYD1939
Features and Controls: PYD1949
Features and Controls: PYD1959
Presetting Controls Before Use
Connecting the Mixer Inputs
Using the Gain Controls
Connecting the Mixer’s Outputs
to Amplifiers
to Recorders
to Zone Speakers
Using Headphones
Connecting the Lamp
Using the Mixer Controls
Turning On the Mixer
Monitoring (”Cueing”) Inputs
Mixing Inputs
Adding Equalization to the Mix
Adding External Effects to the Mix
Using the MicrophoneTalkover Mode
Microphone Tone and Level Controls
Using the MIC Frequency Kill Switches
Using the Mono/Stereo Switch
Using the Crossfader w/Assign Switches
Using the Echo Controls (PYD1929 and PYD1949)
Using the Sound Effects (PYD1939 and PYD1949)
Using the Digital Sampler (PYD-1959)
Troubleshooting
Care and Maintenance
Specifications
Warranty
i
1
2
3
4
5
6
8
9
10
10
11
12
13
14
Stereo Line Inputs let you connect
most high-level audio sources, such as
CD players, tape deck, tuner or VCR.
Dual Purpose Stereo Inputs for
using a turntable with a magnetic
cartridge OR a high lev
el input
source
MIC2 Microphone
connector permits
you to connect a
balanced or
unbalanced low
impedance microphone
with 1/4” plug.
Input Select Switches – set these
switches based on what is plugged
into Phono1/Line1 and Phono2/Line3
input jacks
Output Jacks to connect the mixer to a
receiver or amplifier – choose to use cables
with either 1/4” plugs or RCA plugs.
Zone Output Jacks to connect the mixer
to a second receiver or amplifier powering
speakers in the DJ booth or in a remote
location
Record Output Jacks to connect the
mixer to a tape deck for recording the
mixed program
Power Switch and Red
light Illumination
Equalizer On/Off Switch
Effect Switch
(Send/Receive)
Lets you
connect a sound effect
device, such as reverb,
sampler, etc. and either play
the signal from it or play
another input through it.
BNC Lamp Adaptor Allows
y
ou to connect a 12V/3W
lamp to light the panel
Headphone Jack
Accepts headphones with
1/4” plug
Headphone Level Control
Headphone CUE/PGM
Control
Allows you to listen
simultaneously or separately
to the CUE material or the
active program
Zone Level Control Lets you control the mixer’s overall ZONE
v
olume level, if you set up remote speakers or DJ booth monitors
Zone Mono/Stereo Selector
Zone Balance Control
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Selector
Master Balance Control
Channel Assign Switch Lets you select the input source to be mixed
b
y the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between
the input sources assigned to Channel A and Channel B
MIC Talkover Allows you to lower the
lev
el of the input sources so you can talk
them using the DJ Mic
MIC1/2 Level Controls Lets you control
the MIC lev
els as they enter the mix
MIC1/2 Tone Controls
10-Band Equalizer Allows you to tailor the mixer output to suit
y
our taste or performance environment. Each frequency range can
be cut or boost by up to 10dB.
Dual Display Meter Indicates the levels of Left and Right Master
Channels
Channel CUE Switch Allows you to monitor the selected audio
input source and prepare it prior to mixing it in.
Channel Input Selector Lets you choose the input source to play
for each channel
Channel Gain Control Lets you adjust the gain of the input source
MIC Frequency Kill Switches Allows
y
ou to kill the selected frequency range
instantly for interesting effects. LED
lights to indicate kill is activated.
Effects Send/Receive jacks permits you to either include
externally generated effects (such as a digital sampler or synth)
IN the mix, or to process the mixed sound (echo reverb, etc.).
MIC 2 Input Jack (on input panel)
F
or connecting a balanced or
unbalanced low impedance microphone
with 1/4”plug
MIC 1 Combo Input Jack For
connecting a balanced or unbalanced
low impedance microphone with XLR
-
type or 1/4” plug