Image adj.
Color temp.
Image adj.
Color temp.
Image adj.
Color temp.
Right Left rev.
Top Bottom inv.
Image adj.
Image adj.
Disp.Posi. Menu
Color temp.
Color temp.
Color temp.
Image adj.
Color temp.
Image adj.
Color temp.
Image adj.
Color temp.
Right Left rev.
Top Bottom inv.
Then, press ENTER to execute.
Press ENTER to select an item.
video screen/menu position.
to select an item.
to set or adjust the value.
Then, press ENTER to execute.
select an item.
is bought. The display language can be selected from the following 6
You can see the information.
41
Menu Operations
ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL
■
Quick Reference Guide for PC Menu Mode
* : Factory set value.
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. → (Refer to page 47)
Brightness: Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Contrast: Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Sharpness: Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
All reset: Resets above items to the factory set values.
Yes / No
Setting
Tracking: The lateral size and display area of picture image can be adjusted. (–128 to +127)
→ (Refer to page 46)
Phase: Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 46)
Position: Video screen position and menu position can be adjusted. → (Refer to page 49)
Disp. Posi. / Menu
Resize: The relationship between the number of pixels (resolution) and the screen can be selected.
→ (Refer to page 51)
“1:1”: Picture image is projected with its original size.
Panel: Picture image is enlarged to the full size.
Aspect*: Picture image is enlarged while maintaining the original aspect ratio.
Clamp Selectable clamp position. Normally, set to “BP”. ST / FP / BP*
Color temp.
Color temp.
Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
R-Gain
Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
G-Gain
Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
B-Gain
Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
All-reset
Reset above items to the factory set values.
Yes/No
Options → (Refer to page 52)
Options 1
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
Line display: 5sec* (Line display such as “PC1” or “PC2” appears on top right of the screen for 5 seconds
when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Keystone: Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
PC2 (BNC): RGB* or YP
B
P
R
. Set to RGB when a computer device with analog RGB, V, H/Cs signals is
connected to the PC2 terminals. Set to YP
B
P
R
when a device with component signals (Y, B-
Y, R-Y) or DTV-format signals (Y, P
B
, P
R
) are connected to the PC2 terminals.
Options 2: Press ENTER to enter the “Option 2” submenu.
Right Left rev.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.: OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:] Selectable sleep times. If no-signal condition continues for the period
of selected time (Unite: Minutes), the projector enters the stand-by
mode. 15 / 30 / 60 / OFF*
Options 1: Press ENTER to return to the “Option 1” submenu.
Language Language for on-screen display. → (Refer to page 45)
Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 52)
Input: Shows the terminal name selected by the PC button. (PC1or PC2)
Switcher:
This display currently has no meaning. (“CH.0” is usually displayed to indicate that it is not being used.)
Resolution: Shows the resolution of the input signal being received. (Horizontal × Vertical)
It may not be displayed correctly with some input signals.
Frequency H: Shows the horizontal frequency of the input signal being received. ( kHz)
Frequency V: Shows the vertical frequency of the input signal being received. ( Hz)
Lamp time: Accumulated used hours of the light-source lamp.
