NNEEVVEERR OOPPEERRAATTEE LLAASSEERR IIFF TTHHEE UUNNIITT IISS DDEEFFEECCTTIIVVEE OORR TTHHEE CCOOVVEERR OORR SSEEAALL
IISS DDAAMMAAGGEEDD..
DDOO NNOOTT SSEERRVVIICCEE LLAASSEERR..
The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Do not open the laser unit except to change batteries.
RREEMMOOVVEE BBAATTTTEERRIIEESS IIFF TTHHEE LLEEVVEELL IISS TTOO BBEE SSTTOORREEDD FFOORR AANNYY LLEENNGGTTHH OOFF
TTIIMMEE..
Batteries may leak and damage the laser if it is stored idle for more than
3 months.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
Other than batteries, there are no user-serviceable parts in the laser device.
UUSSIINNGG TTHHEE LLAASSEERR
UUssee ooff ccoonnttrroollss oorr aaddjjuussttmmeennttss oorr ppeerrffoorrmmaannccee ooff pprrooccee--
dduurreess ootthheerr tthhaann tthhoossee ssppeecciiffiieedd hheerreeiinn mmaayy rreessuulltt iinn hhaazzaarrddoouuss rraaddiiaattiioonn
eexxppoossuurree..
SShhaarrpp bblloowwss mmaayy aaffffeecctt tthhee aaccccuurraaccyy ooff tthhiiss
llaasseerr..
Avoid
striking the laser housing.
AADDJJUUSSTT BBEEVVEELL AANNGGLLEE::
1. Remove the battery pack.
2. Loosen the bevel angle knob by
turning it counter-clockwise.
3. Adjust the angle of your cut.
4. Tighten the angle knob securely
by turning clockwise.
LLAASSEERR GGUUIIDDEE
Use of controls or procedures, or performance of proce-
dures other then those specified herein may result in hazardous radiation
exposure.
LLAASSEERR SSAAFFEETTYY
NNEEVVEERR LLOOOOKK IINNTTOO TTHHEE LLAASSEERR BBEEAAMM..
Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
DDOO NNOOTT AAIIMM TTHHEE LLAASSEERR BBEEAAMM AATT AANNYYOONNEE OORR AATT RREEFFLLEECCTTIIVVEE
SSUURRFFAACCEESS..
CCLLAASSSS 22MM LLAASSEERR PPRROODDUUCCTT..
Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
SSTTOORREE OOUUTT OOFF RREEAACCHH OOFF CCHHIILLDDRREENN..
Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
DDOO NNOOTT TTAAMMPPEERR WWIITTHH TTHHEE LLAASSEERR O
OUUTTPPUUTT..
Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
OOPPEERRAATTIIOONN AACCCCEESSSSIIBBLLEE FFIIEELLDDSS::
Wavelength 636-660nm
Laser Power for Classification <1mW CW
19 20
d.
