CA3000
Laney
99
explanation of terms
0
0
A
30C
1
0
Power
Push To Reset Push To Reset
Protect
Bridge
Channel 2
Channel 4
Channel 1
Channel 3
Clip Clip
Clip Clip
Sig Sig
Sig Sig
-12 -12
-12 -12
- 9 - 9
- 9 - 9
- 3 - 3
- 3 - 3
0dB0dB0dB
88
8
0dB
8
0dB
8
Concept PowerConcept Power
LaneyLaney
0dB
8
32
28
29
3026 27
42
48
50
45
46
47
31
25
53
23 2420 21
52
49
51
33
37
39
34
35
36
41
38
40
43
44
Channel 2 input gain: Sets the level of the input signal to channel 2. The visual LED's give the user an
indication of the signal level running through the pre amplifier. The levels should be set as to minimize the
level of clipping. When the red LED is lit the signal is approaching clipping and some degree of sound
degradation may occur if the signal is clipped continuously.
Input level indicator channel 2: Indicates the level of signal running through channel 2
Bridge indicator: This LED indicates that the amplifier channels 1 & 2 are running in bridged mode (37) When
running in bridged mode channel 1's level control acts as the master level control
Bridge indicator: This LED indicates that the amplifier channels 3 & 4 are running in bridged mode (37) When
running in bridged mode channel 1's level control acts as the master level control
Input level indicator channel 4: Indicates the level of signal running through channel 4
Channel 4 input gain: Sets the level of the input signal to channel 4. The visual LED's give the user an
indication of the signal level running through the pre amplifier. The levels should be set as to minimise the
level of clipping. When the red LED is lit the signal is approaching clipping and some degree of sound
degradation may occur if the signal is clipped continuously.
Channel 1 input gain: Sets the level of the input signal to channel 1. The visual LED's give the user an
indication of the signal level running through the pre amplifier. The levels should be set as to minimise the
level of clipping. When the red LED is lit the signal is approaching clipping and some degree of sound
degradation may occur if the signal is clipped continuously.
20
21
22
23
24
22
N
E
U
T
R
I
K
N
E
U
T
R
I
K
N
E
U
T
R
I
K
N
E
U
T
R
I
K
N
E
U
T
R
I
K
N
E
U
T
R
I
K
N
E
U
T
R
I
K
Part:8P-5075
Attention.
Debrancher le cordon
d’alimentation avant
toute intervention.
Avis
Risque de choc
electrique - ne pas ouvrir.
Warning
To reduce the risk of
fire or electric shock do not
expose this appliance
to rain or moisture.
Caution
To reduce the risk of electric
shock do not remove covers.
No user serviceable parts
inside. Refer servicing to
qualified personnel only.
Made in the United Kingdom by BLT Industries Ltd.
Serial No:
!!
CAUTIONCAUTION
RISK OF ELECTRIC SHOCK DO NOT OPENRISK OF ELECTRIC SHOCK DO NOT OPEN
Attention - Remplacer le fusible seulement
par le meme type et le meme calibre.
Caution - For continued protection against risk of
fire replace only with same type and rated fuse
Min Load
4 Ohms
Min Load
4 Ohms
Bridge
Bridge
Amp3
(See Note)
(See Note)
Amp1
Min Load
2 Ohms
MinLoad
2 Ohms
Min
Load
2 Ohms
Min Load
2 Ohms
Amp4
Amp2
Dual Mono
Dual Mono
Channel 4
Channel 2
Channel 3
Channel 1
Caution Refer to users
manual for recommended
speaker connections.
Caution When using
bridge mode only
connect speakers
to the bridge terminal.
Attention - Se referer au manuel d’utilisation
pour la connection haut-parleurs.
Attention En utilisant
en mode “Bridge”,ne
connecter que la
sortie “BRIDGE”.
Supply voltage
~115V
230V
~
~115V
230V
~
Power Consumption
1000 Watts
~50/60Hz
Power Consumption
1000 Watts
~50/60Hz
Ground Link
Ground Link
XLR Pins
Pin1 - 0V
Pin2 - Hot
Pin3 - Cold
Jack Pins
Tip - Hot
Ring - Cold
Shield - 0V
Limiter
Limiter
(Optional)
(Optional)
Off
Off
On
On
In
In
Out
Out
Stereo
Stereo
Bridge
Bridge
Amp4. 1+Hot4,1-Cold4
Amp3. 1+Hot3,1-Cold3,2+Hot4,2-Cold4
Amp1. 1+Hot1,1-Cold1,2+Hot2,2-Cold2
Amp2. 1+Hot2,1-Cold2
Bridge, 1+Hot,1-Cold
NOTE: Speakon™ Pin Configuration
Warning This equipment must be earthed.
Dual Mono/Bridge
Dual Mono/Bridge
Two mains sockets on 115V model only!
25
26
CA MANUAL
