A SERVICE OF

logo

Open as PDF
next previous
46 Chapter 3. TV Setup
Additional Setup Using the
NetCommand Menu, continued
Part 2: Learn A/V Receiver Power and Volume Keys
1. Press tohighlightthecheckboxforPower On.
2. Press
ENTER
ontheTV’sremotecontrolandwhilethe
textPower Onisflashing,pressandholdthe
POWER
or
POWER ON
keyontheA/Vreceiver’sremotecontrol.
3. IfyourA/Vreceiverhasaseparate
POWER OFF
key,press
tohighlightthecheckboxforPower Off.Repeat
theprecedingstepto“learn”the
POWER OFF
key.
If your A/V receiver has no POWER OFF key, skip this step.
4. Press tohighlightadditionalcheckboxesand
repeatstep2fortheotherA/Vreceiverkeys.
5. Whenallkeyshavebeenlearned,press
EXIT
.
Figure 15. Perform NetCommand
“learning” for these A/V receiver
functions.
Part 3: Tell the TV Where Connected Devices
Send Audio
Digital Surround Sound
1. Press
INPUT
todisplaytheInputSelectionmenu.
2. HighlighttheiconfortheDVDplayerandpress
ENTER
to
switchtotheDVDinput.
3. Press
MENU
andopentheNetCommandmenu.
4. HighlightthetextboxunderAV RECEIVER SETUP.
5. Press tomovethroughthelisttoDVD.
ThissettingtellstheTVthatdigitalsurroundsound
fromtheDVDplayerisconnecteddirectlytotheA/V
receiver’s
DVD AUDIO
input.
Figure 16. A/V receiver setup
indicating the DVD player’s audio
output is connected directly to
the A/V receiver’s DVD Audio
input.
6. Press
EXIT
toclosethescreen.
Audio Directly from TV
1. Press
INPUT
todisplaytheInputSelectionmenu.
2. Highlighttheiconforanantennainput(
ANT 1
or
ANT 2
)andpress
ENTER
toswitchtotheinput.
3. Press
MENU
andopentheNetCommandmenu.
4. HighlightthetextboxunderAV RECEIVER SETUP.
5. Press
tomovethroughthelisttoTV.Thisisthelist
ofA/VreceiverinputsyounamedintheAVReceiver
(AVR)Learnscreen(seefigure13).
TheTVsettinghereindicatesthataudiooutfrom
theTV(
DIGITAL AUDIO OUT
or
AUDIO OUT
LEFT/RIGHT
)issenttotheA/Vreceiver’s
TV
AUDIO
input.Audiofrom
ANT 1
and
ANT 2
,
memorycards,andIEEE1394devicesmustgotothe
A/VreceiverfromtheTV’saudiooutputsasthereis
nowaytosendtheaudiodirectlytotheA/Vreceiver.
Figure 17. A/V receiver setup
indicating that the TV’s audio
output (
DIGITAL AUDIO
OUT
or
AUDIO OUT LEFT/
RIGHT
) is connected to the
A/V receiver input named
TV
AUDIO
.
6. Press
EXIT
toclosethescreen.
Analog Audio (e.g., analog VCR)
1. Press
INPUT
todisplaytheInputSelectionmenu.
2. HighlighttheiconfortheVCRandpress
ENTER
to
switchtotheVCRinput.
3. Press
MENU
andopentheNetCommandmenu.
4. HighlightthetextboxunderAV RECEIVER SETUP.
5. ConfirmthatthesettingisatNone,thedefault.
ThissettingtellstheTVtoautomaticallytransferVCR
audiototheA/Vreceiver.TheTVconvertsanalog
audiotodigitalforouputtoadigitalA/Vreceiver.
Figure 18. A/V receiver setup
indicating the analog VCR’s
audio output is automatically
sent to the A/V receiver via the
TV’s audio output.
6. Press
EXIT
toclosethescreen.
IMPORTANT
To hear audio that is sent from the TV to the A/V
receiver, you must have:
•
physically connected the TV to the A/V receiver
•
learned the IR codes for the A/V receiver inputs
• chosenthecorrectinputunderNetCommand
AV RECEIVER SETUP
•
selected the A/V receiver in the Input Selection
menu
If you hear no audio from the A/V receiver, open
the NetCommand menu and perform the proce-
dure in Part 3, “Audio Directly from TV” or “Analog
Audio (e.g. analog VCR.”
Note that all audio should be sent through the TV’s
audio outputs unless you have surround sound
audio going from the device directly to the A/V
receiver.