OPERATION
,_FETYGLASSES
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear safety glasses or eye shields while op-
erating your tractor or performing any adjustments or repairs. We recommend a wide
vision safety mask over spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 5)
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress clutch/brake pedal into full "BRAKE" position
and hold.
Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
will hold tractor secure.
ATTACHMENT CLUTCH
LEVER "ENGAGED" POSI-
TION
IGNmON
KEY
THROTTL_CHOKE
CONTROL
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHERTHAN "OFF" WILL CAUSE THE BATTERY
TO BE DISCHARGED,(DEAD).
NOTE: Under certain conditionswhen tractor is standing
idlewiththe engine running,hotengine exhaust gases may
cause "browning" of grass.To eliminate this possibility,al-
ways stop engine when stoppingtractor on grass areas.
I
CAUTION: Always stop tractor com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 5)
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
battery charging rate,
• Full throttle offersthe best bagging and mower perfor-
mance.
'DISENGAGED"
.PARKING BRAKE
"BRAKE" "'E_IGAGED"
POSITION PosmoN
CONTROL
LEVER
CLUTCH/BRAKE PEDAL
"DRIVE"POS_ION
PARKING BRAKE
"DISENGAGED"POSmON
FIG. 5
STOPPING (See Fig. 5)
MOWER BLADES -
• To stop mower blades,move attachment clutch lever
to "DISENGAGED" position.
GROUND DRIVE -
• To stop ground drive, depress clutch/brake pedal into
full "BRAKE" position.
• Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTIONCONTROL LEVERDOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKEPEDALIS DEPRESSED.
ENGINE -
• Move throttle control to slow position.
NOTE: Failure to move throttle controlto slow positionand
allowing engine to idle before stopping may cause engine
to "backfire".
• Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke to stop engine.
TO MOVE FORWARD AND BACKWARD (See
Fig. 5)
The directionand speed of movement is controlled bythe
motion control lever.
• Start tractor with motion control lever in neutral (N)
position.
• Release parking brake.
• Slowly move motion control lever to desired position.
TO ADJUST MOWER CUTTING HEIGHT (See
Fig. 5)
The position of the attachment lift lever determines the
cutting height.
• Grasp lift lever.
• Press plunger with thumb and move lever to desired
position.
The cutting height range is approximately 1-1/2 to 4".
The heights are measured from the ground to the blade tip
withtheengine notrunning.These heightsare approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cutto appreximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.
11
