A SERVICE OF

logo

Open as PDF
next previous
TABLE OF CONTENTS
5.15.1 Basic parallel operati
on……………………………………………………………………..
Pg. 42
5.15.2 Advanced parallel operation………………………………………………………………..
Pg. 42
5.16 DAISY
-
CHAIN SHUT
-
OFF CONNECTION…………………………………………………….
Pg. 45
5.17 FRONT PANEL LOCKING……………………………………………………………………….
Pg. 45
5.17.1 Unlo
cked front panel……………………………………………………………………….
Pg. 45
5.17.2 Locked front panel………………………………………………………………………….
Pg. 45
CHAPTER 6 REMOTE ANALOG PROGRAMMING………………………………………………
Pg. 46
6.1 INTRODUCTION……………………………………………………………………………………
Pg. 46
6.2 LOCAL/RE
MOTE ANALOG CONTROL…………………………………………………………
Pg. 46
6.3 LOCAL/REMOTE ANALOG INDICATION……………………………………………………….
Pg. 46
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT………..
Pg. 47
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT…………………..
Pg
. 48
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT………………………...
Pg. 49
CHAPTER 7 RS232 & RS485 REMOTE CONTROL
……………………………………………...
Pg. 50
7.1 INTRODUCTION……………………………………………………………………………………
Pg. 50
7.2 CONFIGURATION………………………………………………………………………………….
Pg. 50
7.2.1 Default se
t
ting………………………………………………………………………………...
Pg. 50
7.2.2 Address se
t
ting……………………………………………………………………………….
Pg. 50
7.2.3 RS232 or RS485 sele
c
tion………………………………………………………………….
Pg. 50
7.2.4 Baud rate se
t
ting………………………………
……………………………………………..
Pg. 50
7.2.5 Setting the unit into Remote or Local mode……………………………………………….
Pg. 50
7.2.6 RS232/458 port at Local mode……………………………………………………………..
Pg. 51
7.2.7 Front panel in Remote mode……………………………………………………………….
Pg. 51
7.3 REAR PANEL RS232/485 CONNECTOR……………………………………………………….
Pg. 51
7.4 MD MODE OPTION (Factory Installed)………………………………………………………….
Pg. 52
7.4.1 MD Mode Description……………………………………………………………………….
Pg. 52
7.4.2 MD Mode enable
-
Serial communication mod
e…………………………………………
Pg. 52
7.4.3 MD Mode SRQ………………………………………………………………………………
Pg. 52
7.4.4 Communication Collisions………………………………………………………………….
Pg. 52
7.4.5 MD Mode SRQ Retransmission……………………………………………………………
Pg. 52
7.5 CONNECTING POWER SUPPLI
ES TO RS232 OR RS485 BUS…………………………….
Pg. 53
7.5.1 Single power su
p
ply………………………………………………………………………….
Pg. 53
7.5.2 Multi power supply connection to RS232 or RS485 BUS………………………………..
Pg. 54
7.6 COMMUNICATION INTERFACE PROTOCOL…………………………………………………
Pg. 54
7.6.1 Data fo
r
mat…………………………………………………………………………………...
Pg. 54
7.6.2 Addres
s
ing……………………………………………………………………………………
Pg. 54
7.6.3 End of message……………………………………………………………………………..
Pg. 54
7.6.4 Command r
e
peat………………………………………………………………………
…….
Pg. 54
7.6.5 Chec
k
sum…………………………………………………………………………………….
Pg. 54
7.6.6 Acknow
l
edge………………………………………………………………………………….
Pg. 54
7.6.7 Error me
s
sage………………………………………………………………………………..
Pg. 55
7.6.8 Bac
k
space…………………………………………………………………………………
….
Pg. 55
7.7 ERROR MESSAGES………………………………………………………………………………
Pg. 55
7.8 COMMAND SET DESCRIPTION…………………………………………………………………
Pg. 55
7.8.1 General guides……………………………………………………………………………….
Pg. 55
7.8.2 Command set categ
o
ries……………………………………………………………………
Pg. 55
7.8.3 Initialization control co
m
mands……………………………………………………………..
Pg. 56
7.8.4 ID control co
m
mands………………………………………………………………………..
Pg. 56
7.8.5 Output control co
m
mands…………………………………………………………………..
Pg. 56
7.9 GLOBAL OUTPUT COMMANDS……………
……………………………………………………
Pg. 58
7.9.1 General……………………………………………………………………………………….
Pg. 58
7.10 SINGLE BYTE COMMANDS……………………………………………………………………
Pg. 59
7.10.1 General……………………………………………………………………………………..
Pg. 59
7.10.2 Global commands without respo
nse…………………………………………………….
Pg. 59
7.10.3 Global commands with response………………………………………………………..
Pg. 60
7.10.4 Addressed commands with response…………………………………………………..
Pg. 60
7.10.5 Addressed commands without response……………………………………………….
Pg 61