Filter
Top Products
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:
1-800-692-0200
FAX: 1-800-832-3765
E-mail tech-serv@aiphone.com
Pg. 3
JAW-AZ Instr.
0306JS
SPECIFICATIONS:
Power: Supplied by JA Monitor
Video Input & Output: Composite 1V Peak-to-Peak, NTSC
Connector: BNC
Audio Door input: Use JA-D surface mount door station only
(Can only be used on “Door 2” input of JA-2MCD / JA-2MECD)
Relay: Normally open contact output, 24V DC, 1A
Sensor: Normally closed contact input
Wire: 18AWG, 2-conductor, non-shielded, PE insulation, solid or stranded
Wiring distance: Max. 330' from JAW-AZ to JA-2M(E)CD
Dimensions: 1-5/8"H x 7"W x 4"D
Note:
Only information pertaining to the connection and operation of the JAW-AZ and devices interfacing with it are included here. For
complete installation, wiring, and operational information about the JA-2M(E)CD system, please refer to the Installation Manual
included with the monitor.
OPERATIONS
Activation of the camera from a Monitor:
1. The CCTV camera can be viewed on any of the JA monitors in the system by pressing the MONITOR button repeatedly,
cycling through each video device in order (door 1, door 2, adapter 1, adapter 2) until the desired camera is viewed. If
the JA-D is connected to the JAW-AZ, they will be on the door 2 input. Incoming audio will activate when selected.
2. To initiate 2-way audio with the unit, press and release the TALK button momentarily. (Door 1 & 2 inputs only.)
3. To turn the monitor off, press the MONITOR button again. Otherwise, it will automatically time out after approximately
30 seconds.
Activation of a camera by the Audio Door Station:
1. When the call button is pressed on the JA-D door station, the monitor will turn on with the image from the CCTV
camera, and the chime will sound. The monitor will stay on approximately 30 seconds unless answered.
2. Press TALK momentarily to answer, speaking hands free. Press TALK again to conclude, or unit will time out
automatically in approximately 1 minute.
Interfacing Video with Other Systems:
1. VIDEO OUT connection simply passes the composite video signal on to a standard CCTV system, such as a monitor,
input on a switcher, or DVR. This video signal is live as long as the camera is powered. When using this feature, set the
75 ohm switch to the OFF position.
2. SENSOR input allows a motion detector or other activation device to remotely turn on the camera. Use any device with
a Normally Closed contact. If an audio door station (JA-D) is included, the sensor input cannot be used.
3. RELAY connection provides a Normally Open contact closure that can be connected to an external system. This
contact will be closed whenever the Aiphone system is turned on. This can be wired into a record trigger input on a DVR
or any other external device that needs to be notified when the video and audio is activated to the Aiphone monitor.
Enabling / Disabling ‘Surveillance’ mode:
1. If the JAW-AZ is connected to the C1/C2 inputs of the JA-2M(E)CD, the SENSOR input will only be active if the master
is put into ‘Surveillance’ mode.
2. Toggle the ‘SET’ button on the JA-2M(E)CD to enable surveillance mode. The SET button will illuminate red, and there
will be a one minute delay before the sensor input on the JAW-AZ becomes active.
3. When the sensor contact triggers, the master will emit a tremolo alert tone. If JA-2MECD is used, the picture memory
unit will be triggered.
4. Disable surveillance mode by toggling the SET button.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following measures:
— Reorient or locate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Class B Verification