Filter
Top Products
©American DJ® - www.americandj.com - Emerald Beam™ Instruction Manual Page 4©American DJ® - www.americandj.com - Emerald Beam™ Instruction Manual Page 3
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future ref-
erence.
Emerald Beam™ General Instructions Emerald Beam™ Safety Precautions
Safety Issues: This unit may blow a fuse if the maximum allotted
load of 2 amps (1 amp 220v) is reached. If the fuse needs replacement,
always replace the fuse with same exact type that was remove, unless
otherwise instructed by an authorized American DJ
® service techni-
cian. Use of a different type fuse from that which is recommended may
cause fire or electric shock and will void the manufactures warranty.
• To reduce the risk of electrical shock or fi re, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fi re in case of an internal short. Do not attempt to operate
this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never plug this unit in to a dimmer pack.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked on,
pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 6 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• 4.9mW Green Laser Diode
• Built-In Hanging Yoke
• Sound Active with Internal Microphone
• Fan Cooled
• 16 Programs
• Music Sensitivity Knob
Emerald Beam™ Features
Emerald Beam™ Warranty Registration
The Emerald Beam™ carries a 90 day limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. If the unit is
under warranty you must provide a copy of your proof of purchase
invoice. Please contact American DJ
® customer support for a R.A.
number.
Emerald Beam™ Fuse Replacement
Caution: Always replace with the exact same type fuse, unless oth-
erwise specified by an authorized American DJ® technician. Replace
with anything other than the specified part can damage your unit and
will void your manufactures warranty.
Warning: If you continue to blow fuses, STOP using the unit. Contact
customer support for further instructions, you may have to return the unit
for servicing. Continuing to use the unit may cause serious damage.
Fuse Replacement: Disconnect the unit’s main power supply. Use a
flat head screw drive to pry out the fuse holder. When the fuse holder
is exposed remove the old fuse and replace it with a similar one. The
fuse holder comes with a slot for a spare fuse. When replacing and
checking the fuse, be sure to check the fuse that has the metal ends
completely exposed.
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 532 nm
Max Output : <4.9mW
Class IIIa Laser Product