Filter
Top Products
©American DJ Supply® - www.americandj.com - Starball II™ Instruction Manual Page 4
©American DJ Supply® - www.americandj.com - Starball II™ Instruction Manual Page 3
To optimize the performance of this product, please read these operat-
ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this
manual with the unit, for future reference.
Starball II™ General Instructions
Starball II™ Safety Precautions
• 235 Clear Beams
• 10 RPM Motor
• Easy Lamp Replacement
• Air Cooled
• Built-In Mounting Plate
• Bright ZB-64514 (300w/120v) or ZB-64516 (300w/220v)
• Low Power Consumption (about 2 amps)
Starball II™ Features
• Be sure that the local power outlet match that of the required voltage
for your unit.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fi re in case of an internal short.
• Do not remove the unit cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fi re, do not expose this unit
rain or moisture.
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
Starball II™ Operation
Power Supply: Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ® Starball II.™ The American DJ® Starball II
™
is available in a
120v and 220v version. Because line voltage may vary from venue to
venue, be sure to plug your fi xture into a wall outlet with a matching
power supply before attempting to operate.
General Operation:
Simplicity! Just plug this fixture in, and watch it go. This fixture is
designed to operate as a stand alone unit, there is no need of a con-
troller. It has been tested and the lamp has been installed at the fac-
tory there is no assembly necessary. The Starball II™ is ready to be
plugged in, out of the box. There is no power switch, after plugging the
unit the unit will light up and begin to slowly rotate in a single direction.
If there is no lamp output check the fuse and bulb. If the fuse and bulb
are good, please contact our toll free customer support number for
further instructions. Please do not return the unit to your dealer with-
out fi rst contacting customer support.
Starball II™ Warranty Registration
The Starball II™ carries a one year (365 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
The R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. number
must also be written down on a piece of paper and included in the
shipping container. If the unit is under warranty, you must provide a
copy of your proof of purchase invoice. You may obtain a R.A. number
by contacting customer support at (800) 322-6337.