Filter
Top Products
7 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual
Control Elements2.
A detailed description of all functions of your power mixer can be found in the
following chapters. Please also refer to the enclosed sheet with the numbered
illustrations to get an overview of the control layout.
Mono and stereo channels2.1
The (1) HIGH control in the EQ section governs the high-frequency range of the
respective channel.
Use the (2) MID control to boost or cut the mid-range frequencies.
The (3) LOW control allows you too boost/cut the low-frequency range.
With the (4) MON control you can adjust the volume of each channel in the
monitor mix.
The (5) FX control determines the signal level sent from each channel to the
built-in eects processor; this signal is also present at the FX OUT jack
(see (32)). The PMP980S/PMP1680S has two FX controls (FX 1 and FX 2),
so that you can use two eects simulteneously. Accordingly, it also provides
two eect Aux paths (see (32) ).
Please note that the effects processor signal will be inaudible when the ◊
FX RETURN control (21) is set fully counter-clockwise.
For the mono input channels, the PMP980S/PMP1680S has a (6) PAN(ORAMA)
control which determines the position of the channel signal in the stereo
main mix. The PMP960M has no PAN on the input channels, because it is a
dual-mono power mixer.
The (7) BAL(ANCE) control for the stereo channels of the PMP980S/PMP1680S
corresonds to the PAN control for the mono channels. It determines the
relative volume of the left and right input signals before they are routed to
the stereo main output. The PMP960M has no stereo channels and hence no
BAL control, because it is a dual-mono power mixer.
The (8) LEVEL control adjusts the channel signal level in the main mix.
Input section2.1.1
The (9) CLIP LED is very useful to control the input gain. It should never be
constantly illuminated (only with signal peaks).
The (10) PAD switch reduces the input sensitivity of the channel by
approx. 30 dB, to connect for example line-level signals.
The balanced (11) HI-Z input (¼" TRS) can be used for line-level signal sources,
e.g. keyboards, electric guitars and basses.
Each channel has a balanced (12) LOW-Z microphone input with XLR connectors,
which also supply the +48 V phantom power for condenser microphones
(see (27)).
Unbalanced stereo line inputs with ¼" connectors for stereo channels 7 to 10 (13)
of the PMP980S/PMP1680S. They can be used for connecting keyboards with
stereo outputs or stereo drum machines.
Please remember to use either the microphone or the line input of a ◊
channel at a time, but never both at the same time!
Eects section2.2
List of all multi-eects presets.(14)
LED level meter of the eects processor. Since the PMP980S/PMP1680S (15)
allows you to select two eects simultaneously, it also has two level meters
(DUAL FX). Be sure that the clip LED illuminates for signal peaks only. If it is
illuminated all the time, it is a sign that the eects processor is overloading
and hence producing unpleasant distortion.
The Eect display (PMP980S/PMP1680S: two displays) shows the currently (16)
selected preset.
Turn the (17) PROGRAM control (PMP980S/PMP1680S: one control each for
FX 1 and FX 2) to select an eects preset (preset number starts ashing).
Push the control briey to conrm your selection.
Press the (18) FX IN button (PMP980S/PMP1680S: FX 1 IN and FX 2 IN) to activate
the eects processor.
Main and monitor section2.3
Your power mixer is equipped with two graphic 7-band equalizers. The upper (19)
one processes the monitor signal, the lower one the main signal. Use the EQs
to adjust the sound to the room acoustics.
Press the (20) FBQ IN switch to activate the FBQ Feedback Detection System.
The frequencies causing feedback are shown by the brightly lit fader LEDs.
Simply lower the level of the respective frequency range until feedback
disappears and the LED goes out. Your power mixer oers this function both
for the main and the monitor mix.
Turn the (21) FX RET control to add the eect signal to the main mix (lower)
or monitor mix (upper). The PMP980S/PMP1680S allows you to use two
eects at the same time, it also has two FX controls each for the main
and monitor mixes: when the FX RET 1 and FX RET 2 controls are fully
counterclockwise, no eect signal is added.
The (22) CD/TAPE IN control adjusts the volume of the 2 Track In signal (see (35)).
The (23) MONITOR MASTER control adjusts the monitor output volume.
Use this 5-digit LED meter to control the output level of the monitor signal. (24)
The upper LIM LED illuminates when the internal amp protection circuit
responds to output levels that are too high.
The (25) MAIN MASTER control is used to adjust the main output volume.
Use this 5-digit LED meter to control the output level of the main signal. (26)
The PMP980S/PMP1680S has two rows of LED meters (L/R), because the
signal is stereo. The upper LIM LED illuminates when the internal amp
protection circuit responds to output levels that are too high.
+48 V phantom power is provided for condenser microphones. The phantom (27)
power supply is activated for all channels with the PHANTOM switch and the
PHANTOM LED above the switch illuminates.
Use the (28) POWER AMP switch to determine the operating mode of your
power mixer.
The PMP980S/PMP1680S has three dierent operating modes:
In MAIN L/MAIN R mode it functions as a stereo amplier, i.e. the left
and right main stereo signals are sent to OUTPUT A (L) and OUTPUT B (R).
In MON/MONO mode it functions as a dual mono amplier, i. e. OUTPUT A
sends the monitor signal, and OUTPUT B the main signal (mono). In BRIDGE
AMP MODE the output power of outputs A and B are added and provided
at OUTPUT B.
The PMP960M also has three operating modes, since it can be
operated in two modes with the switch in its upper position
(MAIN/MAIN (BRIDGE) mode), depending on the pin connections of the
speaker cables. In MAIN/MAIN (BRIDGE) mode power of both outputs is
added and provided at OUTPUT B (Locking cable, pins 1+/2+). With the
normal pin connections (Locking cable, pins 1+/1-) a main signal is provided
in this mode at OUTPUT A and B (not bridged). In MON/MAIN mode,
the mixer can also be used as a dual mono amplier, i.e. OUTPUT A provides
the monitor signal, while the main signal is present at OUTPUT B.
Please refer to (44) and (45) as well as chapter 4.4 “Loudspeaker connectors”.