Filter
Top Products
– 4 –
IN230000AV MODELS TL1002, TL1017 AND TL1049
1. Flush the tool with Campbell Hausfeld air tool oil, gum
solvent, or an equal mixture of SAE 10 motor oil and
kerosene. If Campbell Hausfeld oil is not used, lubricate the
tool after cleaning.
2. Lubricate the tool according to the lubrication instructions in
this manual.
3.a. Adjust the regulator on the tool to the maximum setting.
3.b. Adjust the compressor regulator to tool maximum while the
tool is running free.
4. Tighten and seal hose fittings if leaks are found.
5.a. Be sure the hose is the proper size. Long hoses or tools using
large volumes of air may require a hose with an I.D. of 1/2"
or larger depending on the total length of the hose.
5.b. Do not use a multiple number of hoses connected together
with quick connect fittings. This causes additional pressure
drops and reduces the tool power. Directly connect the
hoses together.
6. Replace rotor blade.
7. Remove and inspect bearing for rust, dirt and grit or worn
race. Replace or clean and regrease bearing with bearing
grease.
1. Drain tank. (See air compressor manual). Oil tool and run
until no water is evident. Oil tool again and run
1-2 seconds.
2.a. Install a water separator/filter. NOTE: Separators only work
properly when the air passing through the separator is cool.
Locate the separator/filter as far as possible from the
compressor.
2. b. Install an air dryer.
2. c. If the original separator will not separate all the water from the
air, install a Campbell Hausfeld belt air filter (MP2121).
1. Grit or gum in tool.
2. No oil in tool.
3. Low air pressure.
4. Air hose leaks.
5. Pressure drops.
6. Worn rotor blade in motor.
7. Worn ball bearing in motor.
1. Water in tank.
2. Water in the air lines/hoses.
SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION
Tool runs slowly or will
not operate.
Moisture blowing out
of tool
General Troubleshooting Guide
Impacts slowly or
will not impact.
1. Lack of lubrication.
2. Tool regulator set in wrong position.
3. In-line regulator or compressor regulator
set too low.
Impact Mechanism Troubleshooting Guide
Limited Warranty
1. DURATION: One year from the date of purchase by the original purchaser.
2. WHO GIVES THIS WARRANTY (WARRANTOR):
Campbell Hausfeld
The Scott Fetzer Company
100 Production Drive
Harrison, Ohio, 45030
Telephone: (513) 367-4811.
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld portable air compressor, air tool or supplementary air accessory supplied or manufactured
by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Defects on material and workmanship which occur within the duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL
PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE
CAMPBELL HAUSFELD PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied
with product.
D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
E. Normal adjustments which are explained in the owner’s manual(s) provided with the product, i.e. belts, pressure switch.
F. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets.
G. Electric motor and gasoline engine components are expressly excluded from coverage under this limited warranty. Such components should be returned by the purchaser to
the original manufacturer or to its authorized repair stations for service.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which have failed within duration of the
warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if any, must be borne by the purchaser.
B. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:
A. Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
B. If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact the Campbell Hausfeld Product Service Department (see
paragraph 2).
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
1. Lubricate the air motor and the impact mechanism. (See
Lubrication section of this manual).
2. Adjust the regulator setting of the tool.
3. Adjust regulators in the air system (See Figure 2).