Filter
Top Products
RADIAS synthesizer/vocoder
4
When you operate a switch, a control change CC#80
(SW1) or CC#81 (SW2) will be transmitted on the MIDI
channel of the timbre selected by TIMBRE SELECT.
Switch-on will transmit a value of 127, and switch-off
will transmit a value of 0. When CC#80 (SW1) or CC#81
(SW2) are received, the on/off status of the switch will
change. A value of 64 or higher will turn the switch on,
and a value of 63 or lower will turn it off.
If you want to apply an effect using SW1/SW2, set
the Program Edit mode P03–5: TIMBRE CC-A tab
page “Cntrl” parameter to “O” (Enable). Make this
setting for each timbre.
If you want control change messages to be transmitted
and received, set the Global mode P06: MIDI FILTER
page parameter “Ctrl Chg” to “O” (Enable).
Keyboard aftertouch
Aftertouch from the keyboard is available only if the
M3-M is connected to the TO MODULE connector of the
73/88-key keyboard assembly, or if the RADIAS-R is
connected to the TO MODULE (2nd) connector.
If one of the Global mode P04: MIDI page parameters
“MIDI1”–“MIDI5” are set to A.Touch, you’ll be able to
use keyboard aftertouch as a source for the following:
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
•Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
With the factory settings, “MIDI5” is set to
A.Touch.
When you apply keyboard aftertouch, channel
aftertouch messages will be transmitted on the MIDI
channel of the timbre that is selected in TIMBRE
SELECT. When channel aftertouch is received, the result
will be the same as when you operate the keyboard.
If you want to use aftertouch to apply an effect, set
the Program Edit mode P03–4: TIMBRE-MIDI tab
page “AT” parameter to “O” (Enable). Make this
setting for each timbre.
If you want aftertouch messages to be transmitted
and received, set the Global mode P06: MIDI
FILTER page parameter “Ctrl Chg” to “O” (Enable).
If you connect the RADIAS-R to the TO MODULE
connector, the keyboard’s aftertouch will be
unavailable. If you connect the RADIAS-R to the TO
MODULE connector and the RADIAS-R or M3-M to
the TO MODULE (2nd) connector, not only will the
keyboard’s aftertouch be unavailable, but the
RADIAS-R or M3-M connected to the TO MODULE
(2nd) connector may malfunction when you use
aftertouch. If you make connections in this way,
please disable aftertouch reception on the RADIAS-
R or M3-M that is connected to the TO MODULE
(2nd) connector. (In the Program Edit mode P03–4:
TIMBRE-MIDI tab page, set “AT” to “x”.)
The aftertouch sensitivity of the 73/88-key
keyboard assembly cannot be adjusted on the
RADIAS-R.
Ribbon controller
The ribbon controller is available only if the M3-M is
connected to the TO MODULE connector of the 73/88-
key keyboard assembly, or if the RADIAS-R is
connected to the TO MODULE (2nd) connector.
If one of the Global mode P04: MIDI page parameters
“MIDI1”–“MIDI5” are set to #016±, you’ll be able to use
the ribbon controller as a source for the following:
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
•Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
With the factory settings, “MIDI1” is set to #016.
If “MIDI1” is set to #016, the effect may not return
to 0 when you take your hand off the ribbon
controller. If you want the effect to return to 0 when
you take your hand off the ribbon controller, set
“MIDI1” to #016±.
When you operate the ribbon controller, control change
CC#16 messages will be transmitted on the MIDI
channel of the timbre that is selected in TIMBRE
SELECT. When CC#16 is received, the result will be the
same as when you operate the ribbon controller.
If you want to use the ribbon controller to apply an
effect, set the Program Edit mode P03–5: TIMBRE
CC-A tab page “Cntrl” parameter to “O” (Enable).
Make this setting for each timbre.
If you want control change messages to be
transmitted and received, set the Global mode P06:
MIDI FILTER page parameter “Ctrl Chg” to “O”
(Enable).
If you connect the RADIAS-R to the TO MODULE
connector, the ribbon controller will be
unavailable. If you connect the RADIAS-R to the
TO MODULE connector and the RADIAS-R or M3-
M to the TO MODULE (2nd) connector, not only
will the ribbon controller be unavailable, but the
RADIAS-R or M3-M connected to the TO
MODULE (2nd) connector may malfunction when
you operate the ribbon controller. If you make
connections in this way, please disable ribbon
controller reception on the RADIAS-R or M3-M
that is connected to the TO MODULE (2nd)
connector.