Filter
Top Products
EM360
- The Leader in DJ Technology
©2000 Industries - 5 - http://www.numark.com
CROSSFADER
18. Replaceable Crossfader - achieves clean segues between the
two input channels selected by the Crossfader Assign.
Note: The crossfader is a user replaceable item and subject to
wear. Excessive force can wear out the fader quickly. This is
not a warranted item. In case of failure. Simply unscrew the two
large screws that hold it in place, lift it out and disconnect its
cable. Re-attach the new crossfader and screw the mounting
plate back onto the unit - you’re back in business!
19. Crossfader Assign Knob - determines which input channel will
be heard when the crossfader is moved towards the knob. With
the crossfader centered, both assigned channels are live. Use the
crossfader for fast and seamless segues from one selected
channel to the other.
20. Fader Start – activates the crossfader to send play and cue
commands to your auto-start Numark CD player or other
popular brand. For fader start, attach your mixer to a remote
start CD player using industry standard 1/8”(3.5mm) cables.
When you move the crossfader toward the active channel, the
attached CD player will start. When it is moved away, that side
will cue (similar to pressing the cue button).
KAOSS PAD*
21. Process buttons – send post channel fader audio to the KAOSS
PAD for processing.
22. Process Blend Control – mixes processed (efx)-wet audio with
unprocessed (src)-dry audio. Use this in conjunction with the
KOASS pad to reach desired effects.
23. Preset Program keys (1–6)- You can assign programs to keys
1–6 for convenient selection.
Program assignment:
a) Press one of the PROGRAM MAP keys.
b) Use the PROGRAM knob to select the program that
you wish to assign. If you wish to memorize the
HOLD setting, turn the HOLD switch to ON after
selecting the program, and touch the touch panel to
specify the position.
c) Press and hold the PROGRAM MAP key you pressed
in step 1 for approximately two seconds.
24. Touch panel- You can control the sound by using your finger to
rub or tap (strike lightly) this panel. Never press down too
hard on the touch panel, or place a heavy object on it. Rough
handling can cause it to crack or break. Rubbing or pressing
the touch panel with a sharp object can scratch it, so only use
your finger to operate it. If cleaning is necessary, wipe only
with a soft dry cloth. Using solvents such as thinner may melt
the surface of the touch panel. Note: Affix the included
protective label to extend product life.
25. Hold Switch- When this switch is ON, the current state of the
effect will be maintained even if you remove your finger from
the touch panel.
26. Program Knob- Use this knob to select programs (1–60).
Please see page for a complete listing of effects.
27. Program/Location Display- This shows either the currently
selected program number or the location of the point that you
touched on the touch panel, depending upon mode.
•
When selecting a program: the program number (1–60) will
be displayed.
•
When operating the touch panel: the position you touched
(1.1–9.9) with 5.5 being the center) will be displayed.
Example display: 3.8
vertical position is (3) / horizontal position is (8)
If you select a program that has a Hold On setting, the
program number will be displayed, and then the position
that is being held will be displayed.
28. EFX ON/OFF / Sample Record switch- This can be used to
switch between the effect sound and the direct (unprocessed)
sound, or to record a sample.
When sampling this button lets you record a phrase that you
hear and then play it back by operating the touch panel.
Use the following procedure to record and playback samples.
•
Using the PROGRAM knob or the PROGRAM MAP keys,
select a sample/play effect (program numbers 51–60). The
REC switch LED will blink, and the KAOSS PAD will be in record-ready
mode. At this time, the sound will be output without any change.
•
Press the REC switch to begin recording.
•
Press the REC switch once again to stop recording. The REC
switch LED will light. Even if you do not press the REC
switch, recording will end automatically when the maximum
recording time has elapsed. (The maximum recording time
will depend on the program.)
•
Operate the touch panel to playback the recorded phrase. The
sound will change depending on the position where you
touch the panel. The way in which the sound changes will
depend on the program.
•
To re-record, press the REC switch again. The previously
recorded phrase will be erased, and a new phrase will be
recorded.
If you change programs to a non-sample program, the
recorded phrase will be erased.
*KAOSS technology under license from KORG