Filter
Top Products
20
En
X-PAD (parameter 4)
The cycle at which the cut-off frequency is moved fluctuates
finely.
FLANGER
1
A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT
c, d] buttons.
Short delay
Cycle
Time
BEAT c, d buttons (parameter 1)
Use these to set the 1/4 – 64/1 effect time with respect to the
time of one beat of the BPM.
TIME control (parameter 2)
Use this to set the cycle by which the flanger effect moves.
10 to 32000 (ms)
LEVEL/DEPTH control (param-
eter 3)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the flanger effect is moved fluctuates finely.
PHASER
1
The phaser effect changes according to the beat fraction set with the [BEAT c, d]
buttons.
Cycle
Phase shift
Time
BEAT c, d buttons (parameter 1)
Use these to set the cycle for moving the phaser effect as of
time of 1/4 – 64/1 with respect to the time of one beat of the
BPM.
TIME control (parameter 2)
This sets the cycle by which the phaser effect is moved.
10 to 32000 (ms)
LEVEL/DEPTH control (param-
eter 3)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the phaser effect is moved fluctuates finely.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
BEAT c, d buttons (parameter 1)
Use this to set the degree of the effect sound.
-100–100 (%)
TIME control (parameter 2)
Use this to set the degree of the effect sound.
-100–100 (%)
LEVEL/DEPTH control (param-
eter 3)
Sets the balance between the original sound and the effect
sound.
X-PAD (parameter 4) This changes the degree of the effect sound.
MELODIC
1
2
The mid-range of the sound being input at the point when the [ON/OFF] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
BEAT c, d buttons (parameter 1)
This sets the way in which the recorded sound is played.
TIME control (parameter 2) This sets the way in which the recorded sound is played.
LEVEL/DEPTH control (param-
eter 3)
This sets the balance between the original sound and the
recorded sound.
X-PAD (parameter 4) This sets the way in which the recorded sound is played.
SLIP ROLL
1
2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
When the effect time changes, the input sound is recorded again.
1/1 repeat1/2 repeat
Original
Roll
Changed from 1/2
to 1/1
Effect turned on
BEAT c, d buttons (parameter 1)
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
TIME control (parameter 2)
Use this to set the effect time.
10 to 4000 (ms)
LEVEL/DEPTH control (param-
eter 3)
Use this to set the balance between the original sound and
ROLL.
X-PAD (parameter 4) Use this to set the effect time.
ROLL
1
2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
Effect turned on
Repeated
Original
1/1 roll
BEAT c, d buttons (parameter 1)
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
TIME control (parameter 2)
Use this to set the effect time.
10 to 4000 (ms)
LEVEL/DEPTH control (param-
eter 3)
Use this to set the balance between the original sound and
ROLL.
X-PAD (parameter 4) Use this to set the effect time.
REV ROLL
1
2
The sound being input at the point when the [ON/OFF] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [BEAT c, d] buttons.
Effect turned on
Reversed and repeated
Original
1/1 reverse
roll
BEAT c, d buttons (parameter 1)
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
TIME control (parameter 2)
Use this to set the effect time.
10 to 4000 (ms)
LEVEL/DEPTH control (param-
eter 3)
Use this to set the balance between the original sound and
ROLL.
X-PAD (parameter 4) Use this to set the effect time.
SND/RTN (MIDI LFO)
Connect an external effector, etc., here.
By pressing the [LFO FORM (WAKE UP)] button, MIDI-compatible software and
devices can be controlled using MIDI signals.
SND/RTN
1
Connect an external effector, etc., here.
SEND
RETURN
Effector
DJM-900SRT Serato DJ Edition
12 12
12 12
0
0
ON
TALK
OVER
OFF
9
6
-
26
/
6
-
26
/
6
-
26
/
9
6
-
26
/
6
-
26
/
6
-
26
/
9
6
-
26
/
6
-
26
/
6
-
26
/
9
6
-
26
/
6
-
26
/
6
-
26
/
0
BEAT c, d buttons (parameter 1)
—
TIME control (parameter 2) —
LEVEL/DEPTH control (param-
eter 3)
This adjusts the sound level input to the [RETURN] terminal.
X-PAD (parameter 4) —
MIDI LFO
The MIDI signal (0 – 127) waveform is changed according to the track’s tempo.