Rolls RM65b Musical Instrument User Manual


  Open as PDF
of 4
 
TREBLE: Controls the boost or cut of frequencies above 400 Hz for each channel.
PAN: Adjusts the amount of relative signal to the Right, Left or both Main Out
jacks.
FX SEND: Controls the amount of signal (post-volume control) that is sent for that
channel to the FX Send jack.
MASTER CONTROLS
FX RETURN: Adjusts the amount of signal coming back into the FX Return jack.
MASTER VOLUME, RIGHT - LEFT: Controls the amount of signal sent out the
main Right and Left Output jacks, and sets the overall signal level except for the
Monitor Send and Effects Send jacks.
REAR PANEL
CHANNEL 1
MIC
TRIM
CHANNEL 2
MIC
TRIM
CHANNEL 3
MIC
TRIM
CHANNEL 4
MIC
TRIM
CHANNEL 5
MIC
TRIM
CHANNEL 6
MIC
LINE/
INSERT
TRIM
PHANTOM
POWER
MODEL RM65b
POWER
12 VAC
SERIAL NUMBER
65-
MADE IN U.S.A.
WARNING
:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISQUE DE CHOC - NE PAS ENLEVER
LINE/
INSERT
LINE/
INSERT
LINE/
INSERT
LINE/
INSERT
LINE/
INSERT
STEREO
AUX BUSS
INPUT
FX
SEND
STEREO
FX RETURN
MONITOR
SEND
TRS STEREO
PLUG ONLY
TRS STEREO
PLUG ONLY
6 5 4 3 2 1
RIGHT
OUTPUT
LEFT
OUTPUT
POWER: Connects to the Rolls PS12 12VAC, 300mA power adapter.
1 - 6 CHANNEL MIC INPUTS: XLR input connectors for mic or line level signals.
1 - 6 CHANNEL LINE INPUTS: 1/4” input connectors for line level signals.
Each of these inputs may be reconfigured as INSERTS by moving jumper
connector for each channel located inside the RM65b.
TRIM: Adjusts the amount of input signal from the mic and line input jacks.
PHANTOM POWER: 6 switches for turning on the microphone phantom power for
the XLR inputs, and are numbered for the channel they are assigned to. DOWN is
on, UP is off.
AUX BUS IN: 1/4” TRS stereo input to the main mix bus, and may be used as an
auxiliary stereo input for joining two RM65s together.
FX SEND: 1/4” unbalanced jack for sending the signals assigned by each
channel’s FX Send control out to external effects.
FX RETURN: STEREO 1/4” Tip-Ring-Sleeve jack for inputting signals from
external effects devices. NOTE: THIS JACK IS STEREO ONLY - CONNECTING
A MONO 1/4” TIP-SLEEVE JACK WILL RESULT IN THE RETURN SIGNAL
BEING PRESENT AT THE RIGHT OUTPUT ONLY.
MONITOR OUT: 1/4” unbalanced jack for sending signals assigned by each
channel’s monitor output control to an auxiliary amplifier or monitoring system.
RIGHT and LEFT OUTPUT: 1/4” TRS balanced jacks to be used as the unit’s
main outputs.
USING PHANTOM POWER
Phantom power is a means of powering condenser microphones through the micro-
phone cable. The RM65b has individually switchable 36 volts of phantom power for
each of its 6 channels through the XLR jacks. The DIP switches on the rear of the unit
are for switching the power on and off. When the little switch tab is down, the power is
on. The number on the switch corresponds to the channel that is receiving the power.
If phantom power is not needed, it should be switched off to avoid possible damage
to a microphone, or degraded sound quality.
SPECIFICASPECIFICA
SPECIFICASPECIFICA
SPECIFICA
TT
TT
T
II
II
I
OO
OO
O
NSNS
NSNS
NS
Input Impedance: 20K Ohms balanced
10K Ohms unbalanced (1/4")
Output Impedance: 50 OhmsTRS Balanced
Max Input Level: +10 dBV XLR
+10 dBV 1/4"
Phase Shift: < 10 deg. 20 Hz - 20 kHz
Input Connectors: XLR and 1/4"
Phantom Power: 36 Volts DC
Outputs: 1/4" main balanced +17 dB max
1/4" monitor +17 dB max
1/4" FX send
1/4' TRS Stereo Headphone
Max Gain: (Mains): 60 dB bal/unbal
(Monitor): 55 dB
Tone controls: 12 dB treb, bass cut/boost, 1K Hz center
Max S/N Ratio: 106 dB
THD: < .003%
IMD (SMPTE): < .003%
CMRR: 80 dB
Power: AC adapter 12 VAC (Rolls PS12)
Weight: 7 lbs (3KG)
Size: 19" x 1.75" x 6.5" (48cm x 4.5cm x 17cm)
NOTES:___________________________________________________________
25
 previous