Filter
Top Products
Special accessories 1or MKH 106 P 48
Windscreen MZW 30
The loam-rubber-windshield should be drawn over the sound inlet 01the
microphone when wind disturbances become evident. Largest diameter: 60 mm
Length: 80 mm, Reduction 01wind disturbance: appx. 20 dB.
Shock mount MZS 415
The shock mount can be connected to all tripods, booms, etc. with 3/a" threads
and prevents recordings being disturbed by lootlall or other strong mechanical
disturbanees. Normally used in conjunction with the MZG 415.
Diameter: 35 mm. Length: 80 mm
Microphone clamp MZQ 415
By means01this clampthe microphonecanbeattachedto allstandsandbooms
litted with a3/a"thread. Usedmainly inconjunction withthe MZG 415.
Swivel mount MZG 415
Swivel mount with 3/8" internal thread, can be attached to tripods and the desk
stands MZT 441 and MZT 100. Used together with the MZO 415 and MZS 415.
Due to its removable internal thread insert the swivel mount is also suitable for
mounting on '/," and 5/8" threads.
Desk stand MZT 441
Asturdyandstabledeskstandnormallyused inconjunctionwiththeswivel mount
MZG415 and microphoneclamp MZO415 or shock mount MZS415.
Desk stand MZT 100
This sturdy and stable desk stand with its highly effective sound insulation is
especially weil suited to those recording situations in which knocks and handling
noise are unavoidable e.g. open debates etc. Used in conjunction with the
MZG 415 and the MZO 415.
Desk stand MZT 105-1
A stable and unobtrusive stand tor studio use. It will accept only those
microphones with small Tuchel connectors according to DIN 41 524. Micro-
phones are attached by pushing their Tuchel connectors into the plastic clamp.
Power supplies MZN 16 P 48 and MZN 16 P 48-U
Power supply unit for 48 V phantom powering according to DIN 45596. The
MZN 16 P48 has been especially designed forthe condenser microphones. ..P48
whilstthe MZN 16 P48-U is intended forthe condenser microphones. . . P48-U.
Two microphones can be powered simultaneously f,om each supply unit.
Dimensions: 168 x 120 x 50 mm
Roll-off filters MZF 15 and MZF 15-U
This filter is built into the connecting cable between the power supply source and
the amplifier input. The MZF 15 is intended for the MKH . . . P48 microphones,
whilst the MZF 15-U is designed for the MKH . . . P 48 U versions.
Frequencyreduction at50 Hz . . . approx. 6 dB
at 25 Hz . . . approx. 15 dB
Dimensions: 220 x 152 mm
Connecting cable KA 7-U
The cable is fitted atone end with acannon coupling and atthe other with a cannon
plug connector. It is suitable for (e.g.) connecting the MHK 106 P 48 U to the
power supply unit MZN 16 P 48-U. Cable length: 75 m
Connecting cable KA 1 and KA 7
Tripie conductorshielded cablefitted with3-pin standardplug accordingto
DIN 41524 and3-pin standardsocket.
Lengthof cable KA 1: 1.5m. Lengthof cable KA 7: 7.5 m
10
Description abregee
Le MKH 106 P 48 est un mierophone eleetrostatique a montage
haute frequenee, qui eonvient partieulierement pour les
reportages et les prises de son de haute qualite. Le mierophone
est un eapteur de pression a direetivite omnidireetionnelle qui
favorise legerement et deliberement les hautes frequenees en
son direet. Au-dessus de 5 kHz sa eourbe de reponse presente
un relevement de la brillanee de 4 dB permettant de eapter
eorreetement les ineidenees indireetes. Le mierophone est
insensible aux frottements et aux bruits du vent, une bonnette
anti-vent est toutefois eonseillee pour les prises de son a
I'exterieur. Pour beaueoup de eas d'applieation, on peut renoneer
a la suspension elastique. Comme le mierophone ne possMe
pas de transformateurs, il est insensible aux ehamps parasites
magnetiques.
Courbe de reponse
20 50 100 200 500 1000 2000 5000 10000 20000 cis
Courbe dereponsede consigneavectoleranceMKH106P48, distancede mesure1m.
Chaque microestlivre avecI'origmaldu proces-verbaldes mesuresentre 50 . 20000 Hz.
Principeacoustique
Directivite ..
Bandepassante . . . . . .
Facteurdetransmissionavidea1000Hz
Limitedesaturation
capteur
de pression
.omnidirectionnelle
20 20000 Hz
.20 mV/Pa:!: 1dB
env. 30 Pa
~ 124dB
capteur
de pression
omnidirectionnelle
20 20000 Hz
20 mV/Pa :!:1dB
env. 30 Pa
~ 124dB
env. 70 dB
env. 8 Q
600 Q
200 Q jusqu'a
20 Pa
fantöme
DIN45596
48V:!: 12V,
2--->+, 3--->-
2mA
-10' C - + 70' C
Cannontripolaire
XLR-3selon
IECP130-9
1--->boitier
2--->BF +
3--->BF-
190x155mm
env. 135g
nickelee satinee
ou noire depolie
11
Rapportsignal/bruit (parrapporta 1 Pa,
selonDIN45405) . ..
Impedancedesortiea1000 Hz
Impedanceminimale
env. 70 dB
. env.8 Q
600 Q
200 Q jusqu'a
20 Pa
fantöme
DIN45596
48V:!: 12V,
1--->+,3--->-
.2 mA
-10'C-+70'C
tripolairevissable
normaliseselon
DIN41524
Alimentation
Tensiond'alimentation
r:
Courantd'alimentation
Plagedetemperatures
Connecteur
~
1--->BF+
2--->boHier
3--->BF-
190x140mm
. env. 120g
nIckeleesatinee
ou noiredepolie
-
-
f-- -
-
-
-
-
10dB!