Filter
Top Products
@9SUB MIC LEVEL VOLUME
Adjusts the input level of the SUB MIC input.
#0MAIN MIC / SUB LINE SELECTOR
Selects between MAIN MIC and SUB LINE input.
#1MIC / LINE EQ VOLUME
Adjusts the HI and LOW frequencies for the signal
chosen by MAIN MIC / SUB LINE SELECTOR.
#2MIC / LINE LEVEL VOLUME
Adjusts the input level of the MAIN MIC or SUB LINE
input.
#3MIC / LINE CUE SWITCH
Sends the signal from the MIC or LINE channel to the
monitor section for headphone monitoring. When switch is
on, an indicator lights up.
#4SPLIT / STEREO SELECTOR
When this switch is set to "SPLIT", the master signal is
always heard through the right ear-cup of the headphone.
The signal selected by each CUE SWITCH will be heard
in the left ear-cup. This enables both programs to be
monitored simultaneously, thus assisting in beat mixing.
When this switch is set to "STEREO" no master output is
heard in the headphones, and only the signal selected by
each CUE SWITCH will be heard in both ear-cups.
#5HEADPHONE EQ VOLUME
Adjusts the HI and LOW frequencies for Headphone
monitoring.
#6HEADPHONE LEVEL VOLUME
Adjusts the headphone monitor level.
#7PHONES JACK
Use this jack to connect headphones. Headphones with
an impedance of 8ohm to 600ohm can be used on this
unit.
*For best sound quality Vestax recommends using
Headphones with 150ohm impedance.
#8
MAIN/SUB MIC JACK
[MAIN MIC: XLR JACK (BALANCED), SUB MIC:
PHONE JACK (UNBALANCED)]
Input jack for MIC.
#9LINE INPUT JACK
[LINE: RCA PIN JACK, SUB LINE: 1/4' PHONE JACK
(UNBALANCED)]
Input connectors for line level equipment such as CD
players, CD-R/RW players, MD players, tape decks,
DVD players, DAT and VTR etc.
$0PHONO INPUT JACK
Input jacks for turntables. Connect turntables equipped
with MM (pick up) cartridge.
$1GND TERMINAL
Connect this terminal to the ground lead of the turntable.
This will help to reduce unnecessary noise.
$2INPUT LEVEL SELECT SWITCH[-10/0dB]
Select the attenuation level for the input.
$3BOOTH OUT JACK
[1/4' PHONE JACK (UNBALANCED), XLR JACK
(BALANCED)]
Connects to the DJ booth monitors. This signal is identical to the
HEADPHONE OUT signal.
$4BOOTH OUT LEVEL SELECT SWITCH
Select the attenuation level for the BOOTH OUT.
$5MIC MONITOR IN/OUT SWITCH
Select whether the signal connected to MAIN/SUB MIC
is mixed with the signal outputted from MASTER
OUT1/2.
$6REC OUT JACK
Connects to the input jack of a recording device IE, tape
recorder, MD, DAT, etc. The output level of this jack is
fixed and does not change with the MASTER LEVEL.
MIC / LINE SECTION REAR PANEL
MONITOR SECTION
HOW TO CHANGE THE FADER UNIT
$7MASTER OUT 1/2 JACK
[1/4' PHONE JACK (UNBALANCED), XLR JACK
(BALANCED]
Connect to the input on a power amplifier. These jacks are
Phone type for consumer applications. This mixer has two
sets of MASTER OUT jacks so that the each output level
can be set separately. Therefore, the MASTER OUT can
be used for main output or sub output IE. One for the
main area and the other for entrance.
$8
MASTER OUT LEVEL SELECT SWITCH [-10/0dB]
Select the attenuation level for the BOOTH OUT.
$9MASTER LOOP SEND JACK
Connects the input terminal of an external effector.
(Delay, Reverb, etc.)
%0MASTER LOOP RCV JACK
Connects the output terminal of an external effector.
%1POWER SWITCH
Power on/off.
%2AC IN JACK
Connect the Vestax AC-20 , AC adaptor.
PMC-CX/E 04.4.26 10:16 AM ページ 9