Filter
Top Products
VOX VC-12 EasyStart
V
V
C
C
-
-
1
1
2
2
O
O
v
v
e
e
r
r
v
v
i
i
e
e
w
w
The VC-12 Foot Controller is a pedal board for controlling VOX BUS- compatible equipment, including
VOX Valvetronix amps and VOX Valvetronix ToneLab Direct Recording/Performance Processor. You can
use your VC-12 to do the following:
• Select programs
• Control the VOX-Wah effect
• Control the speed of the U-VIBE effect
• Control the speed of Modulation effects
• Set the delay time by using the TAP switch
• Turn the Pedal, Modulation, Delay, and Reverb effects on and off individually
• Instantly recall a previously-selected program
• Tune your guitar
• Select from 96 programs from Tonelab
• Store your Valvetronix amps program data (32 Programs x 4 Sets =128 programs)
• Select programs on two Valvetronix amps at one time
• Sounds saved on the VC-12 can be transferred to another Valvetronix amp
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
s
s
The VC-12 can be connected to VOX-BUS compatible equipment, including:
AD60VT, AD120VT, AD60VTH, AD120VTH, AD60VTX, AD120VTX, ToneLab
1. Turn off all equipment before making any connections.
2. Connect the included 10 Base-T straight cable to the VOX BUS MAIN connector on the rear panel of your VC-
12.
3. Connect the other end of the cable to the FOOT CONTROLLER connector or VOX BUS connector on your
Valvetronix amp or VOX BUS-compatible device.
R
R
E
E
C
C
A
A
L
L
L
L
s
s
w
w
i
i
t
t
c
c
h
h
In Channel Select Mode, this switch recalls the previously selected program. You can use this to quickly switch
between programs in different banks.
T
T
a
a
p
p
s
s
w
w
i
i
t
t
c
c
h
h
&
&
L
L
E
E
D
D
This switch is used to set the delay time. The VC-12 measures the time between the last two taps to calculate the
delay time. LED blinks to set the time.
C
C
H
H
A
A
N
N
N
N
E
E
L
L
-
-
F
F
X
X
O
O
N
N
/
/
O
O
F
F
F
F
s
s
w
w
i
i
t
t
c
c
h
h
&
&
L
L
E
E
D
D
This switch is used to toggle between Channel Select Mode and Effect On/Off mode.
In Channel Select Mode, switches 1-4 are used to select programs. LEDs 1-4 indicate the currently selected
programs.
In Effect On/Off mode, these switches are used to turn the Pedal, Modulation, Delay, and Reverb effects on and off
individually. LEDs 1-4 indicate whether an effects section is on or off.
V
V
C
C
-
-
1
1
2
2
P
P
r
r
e
e
s
s
e
e
t
t
P
P
r
r
o
o
g
g
r
r
a
a
m
m
s
s
The VC-12 is capable of storing four banks of Valvetronix amp user programs. Valvetronix amps alone
can store 32 programs, whereas the VC-12 offers the user an additional 96 programs for a total of 128
programs (32 x 4 = 128). Programs can be stored from any Valvetronix amp into the VC-12, and loaded
to another amp. As an added bonus, the VC-12 can control two Valvetronix amplifiers at one time. in
The areas assigned to Switches #1, #2, #3 contain 32 factory-preset programs in each memory bank.
Switch #4 is empty. It’s a really good idea to first load your 32 Valvetronix amp programs to Switch #4
so they will be safely stored in the VC-12’s memory.
2