Filter
Top Products
Effects Parameters 269
01V96 Version 2—Owner’s Manual
Appendix
FREEZE
One input, one output basic sampler (Available for
internal effects 1 and 2.).
ST REVERB
Two input, two output stereo reverb.
M.BAND DYNA.
Two input, two output 3-band dynamics processor,
with individual solo and gain reduction metering for
each band.
Other preset effects (COMP276, COMP276S,
COMP260, COMP260S, EQUALIZER601, OPEN-
DECK, REV-X HALL, REV-X ROOM, REV-X
PLATE) are optional Add-On Effects. For more
information on these effects, refer to the Owner’s
Manual that came with the Add-On Effects pack-
ages.
Parameter Range Description
REC MODE MANUAL, INPUT
In MANUAL mode, recording is
started by pressing the REC and
PLAY buttons. In INPUT mode,
Record-Ready mode is engaged
by pressing the REC button, and
actual recording is triggered by
the input signal.
REC DLY
–1000 to +1000
ms
Recording delay. For plus values,
recording starts after the trigger
is received. For minus values,
recording starts before the trig-
ger is received.
TRG LVL –60 to 0 dB
Input trigger level (i.e., the sig-
nal level required to trigger
recording or playback)
TRG MASK 0–1000 ms
Once playback has been trig-
gered, subsequent triggers are
ignored for the duration of the
TRG MASK time.
PLY MODE
MOMENT,
CONTI., INPUT
In MOMENT mode, the sample
plays only while the that the
PLAY button is pressed. In CONT
mode, playback continues once
the PLAY button has been
pressed. The number of times
the sample plays is set using the
LOOP NUM parameter. In INPUT
mode, playback is triggered by
the input signal.
START
1
1. 0.0~2970.5 ms (fs=44.1 kHz), 0.0~2729.2 ms (fs=48 kHz),
0.0~2970.5 ms (fs=88.2 kHz), 0.0~2729.2 ms (fs=96 kHz)
Playback start point in millisec-
onds
END
1
Playback end point in millisec-
onds
LOOP
1
Loop start point in milliseconds
LOOP
NUM
0–100
Number of times the sample
plays
START
[SAMPLE]
2
2. 0~131000 (fs=44.1 kHz, 48 kHz), 0~262000 (fs=88.2 kHz,
96 kHz)
Playback start point in samples
END
[SAMPLE]
2
Playback end point in samples
LOOP
[SAMPLE]
2
Loop start point in samples
PITCH
–12 to +12 semi-
tones
Playback pitch shift
FINE –50 to +50 cents Playback pitch shift fine
MIDI TRG OFF, C1–C6, ALL
PLAY button can be triggered by
using MIDI Note on/off mes-
sages.
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
REV TYPE
Hall, Room, Stage,
Plate
Reverb type
INI. DLY 0.0–100.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–2.4 Low-frequency reverb time ratio
DIFF. 0–10
Reverb diffusion (left–right
reverb spread)
DENSITY 0–100% Reverb density
E/R BAL. 0–100%
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
Parameter Range Description
LOW GAIN –96.0 to +12.0 dB Low band level
MID GAIN –96.0 to +12.0 dB Mid band level
HI. GAIN –96.0 to +12.0 dB High band level
PRESENCE –10 to +10
For positive values, the threshold
of the high band is lowered and
the threshold of the low band is
increased. For negative values,
the opposite will occur. When
set to 0, all three bands are
affected the same.
CMP. THRE 24.0 to 0.0 dB Compressor threshold
CMP. RAT 1:1 to 20:1 Compressor ratio
CMP. ATK 0–120 ms Compressor attack
CMP. REL
1
Compressor release time
CMP. KNEE 0–5 Compressor knee
LOOKUP 0.0–100.0 ms Lookup delay
CMP. BYP OFF, ON Compressor bypass
L–M XOVR 21.2 Hz–8.00 kHz Low/mid crossover frequency
M–H XOVR 21.2 Hz–8.00 kHz Mid/high crossover frequency
SLOPE –6 to –12 dB Filter slope
CEILING
–6.0 to 0.0 dB,
OFF
Specifies the maximum output
level
EXP. THRE –54.0 to –24.0 dB Expander threshold
EXP. RAT 1:1 to ∞:1 Expander ratio
EXP. REL
1
1. 6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
Expander release time
EXP. BYP OFF, ON Expander bypass
LIM. THRE –12.0 to 0.0 dB Limiter threshold
LIM. ATK 0–120 ms Limiter attack
LIM. REL
1
Limiter release time
LIM. BYP OFF, ON Limiter bypass
LIM. KNEE 0–5 Limiter knee
SOLO LOW OFF, ON
If this is on, only the low-fre-
quency band will be output.
SOLO MID OFF, ON
If this is on, only the mid-fre-
quency band will be output.
SOLO
HIGH
OFF, ON
If this is on, only the high-fre-
quency band will be output.
Parameter Range Description