Filter
Top Products
27
Appendix
02 18 mm Harmony 3 Volume OX
mm : 00 - 127 (0...127)
The following NRPN numbers independently control the panning of each harmony note.
The currently-sounding harmony notes are numbered sequentially beginning from the lowest note.
When the value is 0, panning will be random.
For random panning with Vocoder harmony, the pan position will change at each key-on.
For random panning with Chordal harmony, the pan position will change whenever the chord changes.
For Detune and Chromatic harmony, random pan will not function, and the panning will be centered.
02 32 mm Harmony 1 Pan OX
mm : 00, 01 - 64 - 127 (random, Lch...center...Rch)
02 33 mm Harmony 2 Pan OX
mm : 00, 01 - 64 - 127 (random, Lch...center...Rch)
02 34 mm Harmony 3 Pan OX
mm : 00, 01 - 64 - 127 (random, Lch...center...Rch)
The following NRPN numbers independently control the detune amount for each harmony sound.
The currently-sounding harmony notes are numbered sequentially beginning from the lowest note.
02 48 mm Harmony 1 Detune OX
mm : 00 - 64 - 127 (-64...0...+63)
02 49 mm Harmony 2 Detune OX
mm : 00 - 64 - 127 (-64...0...+63)
02 50 mm Harmony 3 Detune OX
mm : 00 - 64 - 127 (-64...0...+63)
1.2.4 RPN (Registered Parameter Number)
This message is used to set Pitch Bend Sensitivity.
RPN MSB and RPN LSB are used to specify the parameter which is to be controlled, and subsequently
Data Entry (refer to 1.2.1) is used to set the value of the specified parameter.
Only the MSB of Data Entry is recognized.
Control# Parameter Data Range
100 RPN LSB 0...127
101 RPN MSB 0...127
The following RPN numbers are recognized.
RPN Data Entry Parameter name and range of values Harmony ch Melody ch
MSB LSB MSB
00H 00H mm Pitch Bend Sensitivity OO
mm : 00 - 24 (0...24 semitones)
Settable in semitone steps over a two-octave range
7FH 7FH — RPN null OO
Set RPN and NRPN numbers to a condition in which no numbers have been specified.
Internal settings will not be affected.
1.2.5 All Note Off
For Vocoder harmony, this message turns off all currently-sounding harmony notes.
Control# Parameter Data Range
123 All Note Off 0
1.3 Pitch Bend
Harmony ch Melody ch
En vv vv OO
n : MIDI channel
vv : data
This message conveys operations of the pitch bender.
It will modify the pitch in the range specified by RPN Pitch Ben Sensitivity.
For the Melody channel, this message will have an effect only when Lead Gender is ON.
2. System exclusive messages
2.1 GM system on
F0 7E 7F 09 01 F7
F0 7E 0n 09 01 F7
This message initializes the tone generator system.
All default values are restored.
n : device number
2.2 XG system on
F0 43 1n 4C 00 00 7E 00 F7
This message initializes the tone generator system.
All default values are restored.
n : device number
2.3 XG parameter change format
F0 43 1n 4C aa aa aa dd F7
This message sends and receives parameters from tables 1 and 2 as a single message unit (combines and sends/receives 2 byte parameters).
n : device number
aa : address
dd : data