A SERVICE OF

logo

Bosch Security
Systems
| 08 Ma
y
2013
EN
|
11
LTC 5136 Series |
Instruction Manual
| Controller Operation
5. Press
ON-1-ENTER
and the address is
set.
Once the Fast
Address
is set, the switch
address
(thumbwheel)
is ignored. The Fast
Address
is
stored to
non-volatile memory,
and will
not
change
if power is
removed
or
factory defaults
are restored (
SE
T
-899-
ENTE
R
).
To reset the dome’s address to the
switc
h
address
(thumbwheel),
repeat the
above
steps and end by
pressing
OF
F-1-
ENTE
R
.
To
check/confirm
the address, call up
the
camera and press
ON-997-ENTER. This
command
causes all cameras to
briefly
display
their
addresses.
6
CONTROLLER
OPERATION
Operation
is quite simple. If the camera number to
be
controlled
is not
visible
in the LED
displays,
use
the
numeric
keypad
to select the desired camera,
then
press ENTER. The camera can now be operated
using
the
appropriate joystick and/or
lens controls.
If
appropriate, pre-position
scenes and
auxiliary functions
can also be
entered.
Note that a delay of more than 3-4 seconds
while
entering
a
selection
results in the
Controller returning
to the default camera entry mode. If this
condition
occurs, start the
selection
again, from the
beginning.
A complete
description
of the controls and
indicators is
provided
in the next
section.
6.1 Cont
rols/
Indic
at
ors
LED
Indicators:
The four digit,
7-segment
LED
display
is used to
display
data entry and the selected
camera
number
.
SET
key:
This key is used to set
pre-position
scenes
of
all
AutoDome
cameras and
Allegiant
Series
Receiver/
Drivers which are equipped with this option.
Operate
the
joystick
and lens controls to position the camera
to
the desired scene to be
programmed.
Press SET,
then
enter the desired
pre-position
number on the
numeric
keypad
(1 to 99). Press ENTER to store the
position.
Certain pre-position
numbers are also used to
program
certain
AutoDome
features. Refer to the
A
utoD
ome
operation
manual for a complete listing of the
available
features.
USER
key:
Press
USER-1-ENTER
to enter
the
Controller diagnostic
mode. This function can be
used
to ensure that all
Controller
LEDs and buttons are
in
working
order. It also
automatically calibrates the
center position of the
analog joystick.
Upon
entering
this mode, the
Controller
sounds a short beep.
The
display
readouts and LEDs behind the first two rows
of
buttons also
illuminate
for about two seconds.
During
this time, the
joystick undergoes calibration,
so
be
careful not to move it until the LED
displays have
gone dark. The operator should note any LED
display
failures during the time they are
illuminated.
Each key may now be pressed to
display
a
unique
code number
associated
with that key. Use the
table
below to ensure that all keys are
operating properly
.
Push the USER key last, as this will cause
the
Controller
to exit the test
mode.
Key Number Key
Number
Set 0009 9
0029
Camera 0025 0
0014
Shot 0010 Enter
0030
On 0018 Clear
0038
Off 0026
Focus
(up)
0043
1 0011
Focus
(down)
0044
2 0019
Iris
(up)
0045
3 0027
Iris
(down)
0046
4 0012 Up 1x53
5 0020 Down 0x51
6 0028 Left 1x52
7 0013 Right 0x54
8 0021
Zoom
(CW) 1x41
Zoom
(CCW) 0x42
NOTE: The
x
digit shown in the number column,
for
up, down, left, right, and zoom values,
indicates
a speed
value, and will
change
based on how far the control
is
activated.