A SERVICE OF

logo

Open as PDF
next previous
3GPSMAP 4000/5000 Series Installation Instructions

The ush-mount method you will use with your chartplotter is dependent on the model. Be sure to follow the instructions for your chartplotter
model.



• Flush-mounttemplate
• Rubbergasket
• Fourthreaded4mmmountingstuds
• Four4mmatwashers
• Four4mmlockwashers
• Four4mmnuts

• Jigsaw
• Maskingtape
• Scissors
• Drill
• Drillbits—
3
/
8
in.(10mm)and4mm
•
1
/
16
in.(2mm)Allen(Hex)wrench
• 4mmsocketorwrench
• Centerpunchandhammer

1. Theush-mounttemplateisincludedintheproductbox.Trimthetemplateandensureitwilltinthelocationatwhichyouwanttoush
mountthechartplotter.
NOTES:
• Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to t the chartplotter and the
connected wires.
• Make sure to leave approximately 1/2 in. (13 mm) of space on the right side of the chartplotter to access the SD card door.
• Mount a 4008/4208/5008/5208 chartplotter 31 1/2 in. (80 cm), and a 4012/4212/5012/5212 chartplotter 39 3/8 in. (1 m) from a magnetic
compass to avoid interference.
2. Theush-mounttemplatehasadhesiveontheback.Removetheprotectivelinerandapplythetemplatetothemountinglocation.
3. Usinga
3
/
8
in.(10mm)drillbit,drilloneormoreofthefourpilotholesinsidethecornerofthetemplatetobegincuttingthemountingsurface.
4. Usingthejigsaw,cutthemountingsurfacealongtheinsideofthesolidlineindicatedontheush-mounttemplate.Usealeandsandpaper
torenethesizeofthehole.
notice
Be very careful when cutting this hole. There is only a small amount of clearance between the case and the mounting holes.
5. Installthefourmountingstudsbyscrewingthemintothebackofthechartplotter.Usethe
1
/
16
in.(2mm)Allenwrenchtotightenthemounting
studsuntiltheystop.Thestudsarecoatedwithareusablethread-lockingpatchappliedatthefactory.
notice
Do not use power tools to tighten the mounting studs. Doing so may cause you to overtighten.
Do not overtighten - you may damage the mounting stud or the mounting holes.
6. Placethechartplotterintheholeandmakesurethatthemountingstudslineupwiththepilotholesontheush-mounttemplateaftercutting,
sanding,andlingthehole.Iftheydonot,markthelocationswherethestudswillfeedthroughthemountingsurface.
7. Usingthecenterpunch,indentthecenterofeachofthe4mmmounting-holelocations.
8. Usinga4mmdrillbit,drillthefourmountingholes.
9. Installtherubbergasketonthebackofthechartplotter.Thetopandbottomsectionswilllineupwiththeholes.Thesidesectionswilllineup
withthenotchesinthecase(forthecover).
10.Placethechartplotterintothecutout.Thefourmountingstudsshouldfeedthroughthefourmountingholesdrilledinstep8.
11.Placetheatwashersandthelockwashersoverthemountingstuds.Thenthreadthehexnutsontothemountingstuds.Tightenallfourhex
nutsevenlyuntilthechartplotterissnugagainstthemountingsurface.