Kenwood KDC-BT945U Manual

A SERVICE OF

next previous

44

|

KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U

DSP Setup

6

Repeat steps 3 to 4 to complete the X’Over

settings.

7

Exit Audio Control mode

Press the [MENU] button for at least 1 second,

and then press it again briefly.

Audio Preset Memory

Registering the value setup by Sound Control.

1

Setup Sound Control

Refer to the following operations to setup the

Sound Control.

- Car Type Selection (page 42)

- Speaker Setting (page 42)

- Car Type Fine Adjustments (page 43)

- X’Over Setting (page 44)

- Manual Equalizer Control (page 39)

- ListeningPositionSelection(page40)

- ListeningPositionFineAdjustments(page40)

2

Enter Audio preset memory mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Detailed Setup” > “Preset” > “Memory”.

3

Select the number to put in the memory

Turn the [VOL] knob and press it when the

desired item is displayed.

Select a preset number.

4

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “YES”.

“Memory Completed” is displayed.

5

Exit Audio Control mode

Press the [MENU] button for at least 1 second,

and then press it again briefly.

⁄

• Register6patternsofAudioPresetMemory.

• Presetnumber“1”:

When you press the Reset, all the sources will be the

setting value which is registered.

• Presetnumber“1”and“2”:

The memory cannot be erased by the Reset button.

• ThisfunctioncannotberegisteredwhentheiPod

Equalizer set in <Preset Equalizer curve Select> (page 39).

X’Over Setting

Fine adjusting the following setting values

corresponding to the X’Over values set in the

section <Speaker Setting> (page 42).

Display Item Range

“X’Over”

“Front” “FC”

Front High Pass Filter

Through, 30*, 40, 50*, 60, 70, 80,

90*, 100, 120, 150, 180, 220, 250*

(Hz)

“SLOPE”

Front High Pass Slope

-6, -12, -18, -24 dB/Oct

“Rear” “FC”

Rear High Pass Filter

Through, 30*, 40, 50*, 60, 70, 80,

90*, 100, 120, 150, 180, 220, 250*

(Hz)

“SLOPE”

Rear High Pass Slope

-6, -12, -18, -24 dB/Oct

“SubWoofer” “FC”

Subwoofer Low Pass Filter

30*, 40, 50*, 60, 70, 80, 90*, 100,

120, 150, 180, 220, 250*, Through

(Hz)

“SLOPE”

Subwoofer Slope

-6, -12, -18, -24 dB/Oct

“PHASE”

Subwoofer Phase

Reverse (180°)/ Normal (0°)

( : Factory setting)

* FunctionofKDC-X994/KDC-X794

1

Select the source

Press the [SRC] button. Turn the [VOL] knob and

press it when the desired item is displayed.

Select a source other than “STANDBY”.

✍ SRC Select mode 2: Pressing the [SRC] button

repeatedly switches source.

2

Enter Audio Control mode

Press the [VOL] knob.

3

Enter X’Over setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Detailed Setup” > “X’Over”.

4

Select the speaker you want to set

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Front”, “Rear”, or “SubWoofer”.

5

Select the item you want to set

Operation type Operation

Selects the item. Turn the [VOL] knob.

Adjust each item. Press the [

4

] or [

¢

] button.

Set the value Press the [VOL] button.