Filter
Top Products
6
V-TONE GMX110/GMX210/GMX212/GMX1200H
3. APPLICATIONS
PHONES connector is used, the internal loudspeakers and
the speaker outputs are disconnected.
Those signals that are connected to the SLAVE IN
connectors are directly routed to the V-TONEs power
amp. This way, you can connect an external guitar preamp
or modeling amp (e. g. V-AMP 2 or V-AMP PRO) without
using the internal preamp on your V-TONE.
+ The GMX110 features no SLAVE IN connectors.
You can take the stereo signal of your V-TONE at the
TAPE outputs (RCA) and record it, for example.
The TAPE inputs (RCA) let you feed an additional stereo
signal into your V-TONE. You can play along to the beat of a
drum computer or play to the music from a CD or MD player.
You can take the stereo signal of your V-TONE at the LINE
outputs to record it or route it to a P.A. system. This output
is independent from the MASTER control and does not
render the AUX signal. Additionally, its frequency response
is corrected (speaker simulation).
+ The GMX110 features no LINE outputs.
Use the AUX IN control to adjust the volume of the signal
that is fed in via the AUX IN connectors (e. g. drum
computer, playback).
+ On the GMX110, this control is called TAPE INPUT. It
regulates the volume of the signal fed in at the
TAPE IN connectors.
The AUX IN lets you feed an additional stereo signal into
the amp (except for the GMX110). This way, you can play
to a backing track that supports you on-stage but should
not be audible via the LINE outputs connecting the GMX210/
GMX212 to the P.A. system. Additionally, you can use
AUX IN together with the INSERT SEND as a parallel insert
loop. To do that, connect the INSERT SEND to the input of
your effects device; connect the AUX IN (TAPE IN on the
GMX110) to the output of your effects unit (the INSERT
RETURN connector should not be in use!). This way, the
signal flow in your V-TONE is not interrupted. With the
AUX IN control, you can determine the extent to which the
external effects unit alters the original signal. Keep in mind
that the effects unit should be set up to 100% effects
signal (100% wet).
Your V-TONE features a serial insert loop that can be
used to connect external effects (e. g. a Wah pedal).
Connect the SEND connector on the V-TONE to the input
of your effects unit. The SEND connector is tapped into
directly before (i.e. pre) the digital signal processor (DSP)
of your V-TONE. Connect the output of your external effects
unit to the RETURN connector of your V-TONE.
+ You can use the INSERT SEND as a parallel output
without the effects. This is useful when you for
example need to record a dry guitar signal. As long
as the RETURN connector has nothing plugged into
it, the signal is not interrupted internally.
Use the SPEAKER OUT connector to connect one additional
loudspeaker to your GMX110. This loudspeaker should
have an impedance of 4 Ω. When this connector is used,
the internal loudspeaker is automatically muted. Additional
information about connecting an external loudspeaker can
be found in section 6.2.
FUSE RETAINER/VOLTAGE SELECTOR. Please make
sure that the voltage indicated by the voltage selector
matches the local voltage before you connect the unit to
the mains. Always replace blown fuses with fuses of the
same type. Some units feature a fuse retainer in which a
selection between 230 V and 120 V is possible. Please
beware: When using your unit outside of Europe with
120 V, a higher fuse rate is required.
Power is supplied via an IEC connector. The matching
cable is provided with the unit.
SERIAL NUMBER. The serial number of your V-TONE is
located on the rear. Please send the completely filled out
warranty card within 14 days of purchase to assure
unproblematic warranty processing in the future. Or use
our online registration form at www.behringer.com.
3. APPLICATIONS
The V-TONE features many different connectors, letting you
live up to all kinds of application challenges. We have listed just
a few examples of how flexibly your V-TONE can be used:
3.1 Practice setup with playback