Filter
Top Products
Page 3 of 8
once only available in the studio is ready to
go wherever you do. Built-in, boutique-caliber
mic preamps with switchable +48 V phantom
power make it possible to use either dynamic
or condenser mics with the PMP Series. The
PMP6000 gives you 12 mic inputs while the
PMP4000 and PMP1680S each give you 8 mic
inputs.
Built-in Digital Eects Processor
The new generation of PMP mixers come
equipped with 24-bit FX processors, giving you
100 mind-blowing digital eect presets such
as delay, chorus and reverb. Apply them to
any channel, as well as to the monitors and
main output. In case you’re pulling double
duty as sound engineer and performer, the FX
processors features a footswitch jack for remote
on/o. Of course, if you have treasured outboard
gear you’ve grown attached to, these mixers can
integrate them into the mix while leaving out
the built-in FX processor.
Changing the Channels
The PMP Series gives you excellent exibility
to accommodate whatever a performance
requires. You get 12 (PMP6000) or 8 (PMP4000
and PMP1680S) channels for mics, guitars
and other mono instruments. Stereo channels
13-20 (PMP6000), 9-16 (PMP4000) and
7-10 (PMP1680S) are designed to work in
pairs as stereo channels, or independently for
more mono instruments. All mono channels
have 3-band EQ, switchable Low cut lter for
eliminating infrasonics, and Clip LEDs to indicate
when the input signal is too hot.
A STANDBY switch (PMP6000 and PMP1680S)
mutes all mic channels during breaks, preventing
the microphones from picking up noise or
interference. You can leave all faders untouched
while you play a CD via the CD/TAPE inputs.
The FBQ Feedback Detection
system automatically shows you which
frequencies are causing feedback.
Just touch the FBQ button and watch
the red LEDs on the 7-band graphic EQ
pinpoint show you which frequencies
to adjust for optimized sound,
without the feedback.
The Ins and Outs
Use the CD/TAPE IN RCA inputs to feed
in external stereo signals from CD players
or tape decks. The VOICE CANCELLER
switch eliminates the vocals from
pre-recorded music for instant
karaoke applications.
CD/TAPE OUT RCA outputs send
line-level signals from the mixer to a
recording device. The left and right
main outputs can be used for a variety
of purposes, including connecting more
power amps. Connect monitor power
amps or active monitor speakers to the
MON SEND output. Powered outputs
on these mixers are available in
professional Speakon-compatible format
for secure operation.
Continued on next page
MULTI-FX
PROCESSOR adds
selected sound
eect to any
channel whose FX
knob is turned up
GRAPHIC EQ
adjusts specic
frequencies
FX TO MON and
FX TO MAIN knobs
adjust amount of
signal from internal
multi-FX processor
included in main or
monitor mix
PHONES/CTRL
ROOM knob
adjusts headphone
and control room
output volume
VU METERS
display main and
monitor output
signal levels
CD/TAPE adjusts
volume of CD/TAPE
IN signal in main or
monitor mix
MAIN 2 knob
(PMP4000/6000)
adjusts output of
MAIN 2 jacks
SURROUND
knob adjusts the
amount of stereo
enhancement on
the mix. Press the
XPQ TO MAIN
button to activate
the eect
STANDBY
button mutes
all mic channels
(PMP6000)
FX (SEND)
fader(s) adjust
signal sent to
internal FX
processor and FX
SEND jack(s)
MON (SEND)
fader(s) adjust
output of MON
SEND jacks and
OUTPUT A when
using MON 1/
MONO mode
MONO fader
adjusts output
of MONO OUT
jack
MAIN fader(s)
adjust the
output of
main signal
PHANTOM Switch
provides 48V to
the XLR inputs
for use with
condenser mics
POWER AMP
switch selects
operation mode of
power amp
SPEAKER
PROCESSING
switch allows mixer
to compensate
for speakers
with limited low
end frequency
response
EUROPOWER
PMP6000
PMP4000
PMP1680S