Filter
Top Products
FADER REPLACEMENT
1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE
SCREWS (C) CAREFULLY REMOVE OLD CROSS FADER AND
UNPLUG CABLE (D)
2. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
3. SCREW THE CROSS FADER
TO MIXER WITH THE FADER
PLATE SCREWS (B)
4. REPLACE THE FACE OF THE
MIXER AND SCREW THE FOUR
SCREWS BACK IN AND REPLACE THE FADER KNOBS.
MASTER OUTPUT SECTION
The MASTER OUTPUT SECTION rotary knobs adjust the volume of the
MAIN and ZONE output and also the LEFT and RIGHT BALANCE of
those outputs.
MIXER CHANNEL
(NOTE: ALL 5 CHANNELS HAVE THE SAME FEATURES)
CHANNEL INPUT SELECTOR
The CHANNEL INPUT SELECTOR switches allow you to choose which
input will be controlled by that channels corresponding
volume FADER.
For example on CHANNEL (1) the INPUT SELECTOR allows you to
choose between LINE 1 in or MIC 2 in, and on CHANNEL (2) The INPUT
SELECTOR allows you to choose between PHONO 1/LINE 2 and LINE 3 ,
and also on CHANNEL (3) the INPUT SELECTOR SWITCH will let you
choose between PHONO 2/LINE 4 and LINE 5 then on CHANNEL (4) you
may choose between LINE 6 and MIC 3 and on CHANNEL (5) you can
choose between LINE 7 and LINE 8 . (see CONVERTIBLE LINE INPUT)
for PHONO 1/ LINE 2 and PHONO 2/ LINE 4 switching.
CHANNEL ROTARY GAIN
The CHANNEL ROTARY GAIN allows you to boost the signal of each indi-
vidual channel depending on how low or high its input level is
CHANNEL VOLUME FADER
After you have chosen which input you will use with the INPUT SELEC-
TOR the corresponding CHANNEL FADER will allow you to adjust the vol-
ume for that particular CHANNEL.
CHANNEL CUE BUTTONS
The CHANNEL CUE BUTTONS allow you to individually choose which
channel you wish to monitor in your headphones, you can monitor one at a
time or any combination of the five.
3 BAND EQUALIZER
The 3 BAND EQUALIZER adjust the tone of each CHANNEL by giving
you a choice 3 frequencies (BANDS) to adjust , from LOW,
MIDRANGE (MID) and HIGH’s ,you can use the adjustment knobs to
higher or lower the 3 seprate frequencies till the sound of the music pro-
gram is approppriate for your listening enviroment.
CONTROLS CONTINUED
10
14
11
15
19
“Ipod Friendly” Cable: To connect your Ipod or other
Digital Media Player, use the included Ipod cable.
Connect the 1/8” end of the cable to the headphone
or line out jack of your player, and connect the RCA to
the line input of your mixer.
SPECIFICATIONS
INPUTS:
Phono.....................................................................................3mV,47 KOhm
Line..................................................................................150 mV, 27 KOhm
MIC......................................................................1.5 mV, 1 KOhm Balanced
OUTPUTS:
Max...................................................................................20V Peak-to Peak
Rec.....................................................................................225 mV, 5 KOhm
GENERAL:
Frequency Response.................................................20Hz - 20KHz +/- 2db
Distortion..........................................................................................< 0.02%
S/N Ratio...........................................................................Better than 85 dB
Headphone impedance..................................................................16 Ohm
Power Source (external)......................................................AC 15V, 500mA
Unit Demensions.....................................................................19” x 3.3” x 7”
..........................................................................(482.6 x 83.82 x 177.8 mm)
Weight................................................................................6.35 lbs (2.88 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVEMENT
MM-3000
CROSS FADER
The CROSS FADER allows you to mix evenly from one source to another.
On the MM-3000 The CROSS FADER is assignable between all (5) chan-
nels. The CROSS FADER on the MM-3000 is also removable and if the
need arises can be replaced.The RG-45 (RAILGLIDE
™) DUAL-RAIL
CROSS FADER, which has internal dual stainless steel rails that allow the
slider to ride smoothly and accurately from end to end can be purchased
from your local GEMINI dealer.
CROSSFADER ASSIGN SWITCH
The CROSSFADER ASSIGN SWITCH allows you to assign any of the
mixer CHANNELS to the crossfader. The CROSSFADER will then mix
smoothly between the two assigned channels. Any channel not assiged to
the CROSSFADER will work normally.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS
CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
12
22
13